Viewing all customer Discussions for:

Door & Window

Have (4) 6' Peachtree sliding doors alomost 30 years old. 1. Tracks are worn. One with noticeable dip likely from track digging in. Do you recommend 80-102 or is there an advantage of going with 80-106. 2. I understand that 80-106 can be revited or screwed down. What about 80-102. I used a ... (cont.)

Can you help me identify this? Stamped on the spring channel is "3040" and BSI - TB.

Hello. I purchased 10 bronze 39-227B cranks a few weeks ago. I need 20 more. Are they no longer available in bronze? Thanks!

I need to replace the channel balance on Milgard windows. The identification printed on the channel is 32 5 kv cmc 2. Can you pleas erell me what channel balance I need? Thanks, Dan B.

Hi, I have tilt window, 3/8", GREEN tip; however, that brings us to the only choice of a RED tip. [then buying tension tool and 1/2" shoes] Thanks for the help. Bonnie

1/2" x 29" Stamped: 28F Top and Bottom Attachments per attached photos

For a double aluminum and glass door, the weatherstrip at the door meeting is something we have not run into before. It is worn-out and we are contracted to replace it. Wondering if you recognize and can offer a replacement for this weatherstrip with metal carrier that is inserted in the door edge ... (cont.)

I think I located my window channel balance as Series 350 (It is 22 inches long and the number on the surface is 21100). The top sash guide should be 18 - 172 Here are the pic. Pls help. I need several Tks Alberto

Hi, I need to replace four Caldwell block and tackle channel balances that are about 15 years old. On the metal front there are printed numbers and letters "31 3 DQ Caldwell". Width is 1/2" and metal end-to-end length is 32". It comes with winged top and bottom pieces. I have attached 3 pictures to ... (cont.)

I need a new balancer for an Andersen window. The number on the balancer is J345#23 4-87. I think the replacement balancer is 637. Is that correct? Thank You, Tom

I am having hard time identifying my window balance on your site. The length is 29", width: 1/2", depth: 9/16". The balance sides are hemmed. The letters on the back are marked as: 28 3 FU CMC 4. I am including a few photos so that you can help me identify which one I need. I would appreciat ... (cont.)

I need to replace 2 channel balances. I believe I have the 27" 380 series and the old one has "26 5 AW CMC 2" imprinted on it. The sash weighs 15 lb. I'm not sure which option I need. Can you help? Thanks! Ryan

I am the delivery manager at Cardis Furniture and we have a customer who has Certainteed brand windows that are over 10 years old. During a hoist of furniture, the windows were removed to accommodate the delivery. As a result, a clip was broken on our customer's window, making it impossible for her ... (cont.)

I am in need of one balance (not sure if this is the correct term for the part: image attached) with dimentions 29 inches in length, 0.5 inch in width, and 0.5 inches in depth (weighs about one pound). These are from a 25 inch wide x 70 inch long window and it looks like "U B 29C" is printed along t ... (cont.)

I have all Kinco windows in my house and most are "sprung". That is the plastic piece that holds the spring in the sash frame is broken and the spring has flown to the top of each track. What can I do and what do I need to fix them. I have supplied photos to help you see what I am talking about. ... (cont.)

g3287 type a ali-class a window balances these are pics of our peachtree window channel balances. we need 2 sets of 23-1/4", one set of 16-1/4". the window weight for the longer balance is 15 lbs, and the window weight of the shorter balance is 12 lbs.

balance kit needed for peachtree window I.D. No.2518. 1/2 x 26 3/16 lg.

Dear Swisco, I'm looking for some steel rolers and nylon axel pins for some sliding aluminum windows. The rollers are 5/8 diameter, 3/16 thick with a 5/32 axel hole to accommidate a 1/8 nylon pin. The axel pin is 3/4 long. Any ideas? Thanks, Dennis

Hello, I am trying to locate a replacement for this top channel balance guide. It has a part number of H-719, but I am unaware of the brand. I've attached pictures. It is 7/8" across at the bottom and 9/8" across at the top. It is 9/16" thick at the midpoint and 3/4" thick at the top. It doesn' ... (cont.)

I need to buy a new crank assembly and cover and I'm ok on what I need but I can't distinguish the bronze vs dark bronze. I don't need a handle but as it is the same color that I will need for the cover, is handle part #45012 bronze or dark bronze? Thank You