Viewing all customer Discussions for:

23-067 Front, 1/4" Offset Closet Door Hanger, 1" Dia.

Need input on available replacement parts for 3 sets of closets door thickness: 1 3/8 inch thick front bypass door:1 inch wheel, offset 3/8 inch rear bypass door 1 inch wheel, offset 1 inch

I would appreciate your help identifying a Swissco part to replace a front closet door hangar. 15/16" to 1" wheel. Closet door is 3/4" thick. Thank you.

Old (1952?) solid wood closet door rollers needed... I need 12 paired sets! Square flat channel track, Square flat rollers 1 1/4 diameter, 3/4" offset with the wheel coming back 1/2" Any hope of finding? How about just 1 1/4" flat rollers? (I could maybe use existing brackets) Thank you for any ... (cont.)

I need parts for our wooden closet door. One of the doors has been displaced, and the doors collide (friction) with each other. Dimensions: Width 43.6 inches, Height: 68 inches

It says Stanley on it.

Thank you for responding to my request. I am looking to replace all of the hanging roller assemblies for four closets. Each closet has two doors and each door has two assemblies for eight 'front' assemblies needed and eight 'back' assemblies required. I have attached a picture of two assemblies ... (cont.)

Looking for parts or replacement. The roller is 1 inch diameter

I'm looking for hardware for bypass closet door replacements. I can't find any number or brand on the existing hardware. The home is from 1956, so the doors could be this old. I need two sets for each of two rear doors. I'd appreciate your help.

The only thing it said A on the back ,the house was build in 1956, what part I should use I can't find anything flat like that piece. What you recommend.

Looking to replace closet sliding door hanging hinge with 1 inch plastic wheel that has ball bearings in it. Cannot find at local stores only smaller versions

Do you sell this product?

How about a National Home built in the 1950s with 8ft tall steel bypass doors! Some offset- maybe 1/4 or 3/8? Will need 8 rollers (4 pair) if we can find the correct fit. Thanks

I need these rollers for my sliding doors.

Hi my name is Mike Hoffer at Shands Starke Regional Medical Center. I am looking for some new rollers for some sliding doors I have in my O.R. I have attached a picture, it says Keil 550 on it, as well as front ¾ rear 1 3/8. If you could help me identify what I need would be great. Thank YouMike ... (cont.)

I am trying to identify and obtain proper closet door replacement roller hardware for the system depicted in the attached sketch. The original brackets are missing on the outer door so I am not sure of their exact configuration. The OD of the existing inner door roller is 1 1/16" and it is 1/4" wide ... (cont.)

I have 2 sliding doors, made in 1955, which have wheels made by "Cox & Sons", Pasadena, CA. The 1" DIA wheels have NO ball-bearings and are badly worn-out, see 2 pix for dimensions. The spades are 1" wide. What are the right replacements WITH ball-bearings you can offer and at what cost, incl shipme ... (cont.)

I have a set of old closet doors. The rollers were kind of worn out. I'd like to seek for replacements. I tried to measure and draw the dimensions. Hopefully those files make sense. Thanks a lot. Amy

Looking for some hardware for sliding by pass doors for a closet in my 1912 house. Length of hardware is 3 5/8 bottom of bracket to top of wheel About 3/4 height on wheels, could have been 1 inch but they are very worn metal wheels. the wheel edge thickness is very narrow. Its about 1/2 inch ... (cont.)

I have a set of sliding doors in a bedroom closet. The rear door of the set has good roller hardware. The front door of the set has no hardware, as it has broken throughout the years. The rear door hardware measures as the following hardware, found on your site. 23-186 Rear Closet Door Hanger, 1 ... (cont.)