Viewing all customer Discussions for:

Door & Window

My house was built in 1989. There are no number parts on the old balances.

Hi can you help me identify this roller? 1.5 inch steel roller. The aluminum frame is 1 15/16 wide by 1 9/16 high. It says DISCO 1214 on the side. There are no other markings I can see Thanks

Can you tell me where to get a replacement for this part? Both the "ears" broke and it no longer holds the drawer to the slide. This is a Thomasville credenza with wooden center of drawer slides.Thanks!LuAnn

No markings to help. Thanks Andrew

You have lots of items that are close and may likely work ...so here we go.I have included 5 pictures. The Outside diameter of the flat brass roller is 9/16".The pin (.172") that holds the roller is worn along with the elongated hole in the roller. As a result, the rollers are recessed and the slide ... (cont.)

I do not see any identifying wording, but I have not been able to remove these parts yet. I was hoping to accomplish the removal and replacement in all one repair session. I am an accomplished DIY-er, but the window is heavy as it measures 42" by 32" approximately, so I will need to find a helper f ... (cont.)

26 7/8" Stamp 26 3 (B.S.I.)

The plastic trim from my window broke and I have a hard time finding the right part.

I have Larson Impact windows.The metal channel is 30" overall length is 31". Markings " 29HD56 "

I'm looking for below handles and need 40 of them. I have the unit on the wood and only looking for the handles if that's an option. The size is approx 5.5inches

Hi I thought I ordered the right one but I didn't. Any way I could be directed to the right one? Also could someone translate this label? Thanks!

Looking for a sliding screen door handle that can lock on Outside and inside to keep cats from escaping when I use the door.

I have non-tilt windows. The width of the channel balance is 1/2 inch. I have some 28" in length stamped B.S.I. 2730 and some 24" in lenght stamped B.S.I. 2330. See photos attached.

I'm pretty sure I figured out what I need is the S351-36. I don't have the exact weight of the window as I have no scale here at our vacation home. It looks as though this is mainly a rust issue with the old balances, the bottom pulley and spring is very rusty as these are 23 years old and are in ... (cont.)

Screen door wheel. No marking on either door or part.

Gentlemen, I hope these pictures and my measurements are enough info to determine availability of replacement parts for my window locks. A few of the handles(?) are loose and seem to be not secured to the unit. Thank you for any help you can offer. Unit screw holes are 1 7/8" apart. Backs ... (cont.)

I recently had some second hand Jeld Wen windows installed in a remodel. The casement window lost the handle in the transition. I need to get some replacement but there's no recommendations to which handles go with which crank. Just trying to find images of the hardware in tact has proven difficult. ... (cont.)

Can you confirm what style/type of lock I need to replace this one that is broken?

Hello, Do you have this CTG 1.5 inch diameter roller set for my sliding screen door? My patio door with a sliding screen door has this stamp on glass. If not, I need to replace the sliding screen door measure at 35.5"x 78.5" which is hard to find. Could you please advise if you have the roller ... (cont.)

WANTED TO SEE IF YOU CARRY THE BALANCE STRIP OR THE PART THAT FITS ON THE BOTTOM THAT FAIL. IF YOU HAVE A BALANCER THAT FITS OR HAVE ONE THAT IS MORE ROBUST, PLEASE LET ME KNOW. THESE WINDOWS WERE INSTALLED IN 2008. NAMI NEFC 100/200 (SERIES BMDH) (MST 3856)