Viewing all customer Discussions for:

Weatherization

T Slot is .187 Bulb is 7/16 Total width is 7/8

Looking for the bottom outside door weather stripping on the movable door. And any other weather stripping for the rest of the door since it looks like I would have to remove the door to install a new one. Thx

Q-Lon

This is for Kolbe casement windows installed in 2003. This weatherstrip is located on the jamb not the sash and is a foam filled off set tube 3/8" in diameter. I need 1000 feet of this one. I nedd 2 additional profiles.

Standard Pella metal clad exterior patio door in 8LF height from around 1992. Photos of damaged strip in place and pulled out at the end to show kerf and bulb.Dimensions are 1/4" base extension length, two bulbs - large = 1/2" diameter & small = 1/8 diameter.

I need replacement weatherstripping for my Silverline window

We're looking for replacement weather stripping for crank out windows. Series 8100 AAMA/NWWDA 101/I.S.2-97 and AP-LC25-48x36

Weather stripping on bottom of lower sash and top of upper sash where sash meets the casement. The seal was foam filled, but in the picture the vinyl outer layer has fallen off completely. The anchor has 2 barbs on each side of it. I don't really see it in your list of products, but maybe I miss ... (cont.)

SGcc-1110 4021 32511256 Herculite patio door 76 X 80 manufactored 2004, I need a replacement snap-in weather strip. Please contact me as soon as possible with part number and ordering information

One inch thick, double brush vertical wearher strips. Aluminum is 1 inch commercial door. Can you get just the brush or both pieces? Andrea

Hello, trying to figure out what type of replacement weather stripping I should replace this with. It has like a center divider in it. Thanks! Measurements in pictures.

Do you guys have angthing like this black rubber type of glazing height is about 11/16 but could be longer by a bit if need be. total width is about 7/16 and the part that presses into the channel is about 5/16 wide and between 3/16 to 1/4 deep thanks in advance for your help

I have a custom bilt storm door fly from Lowe's. The bottom seal is worn T-shaped the top part that goes into the door track is 3/8 inches long and the seal part is 1/2 inch long

Hello, I'm looking for something that goes in the track of the windows because the cold air comes right up those side tracks . My windows go up and down and the bottom tilts out or removes for washing. .

I don't see any identifiers on the door to tell you what brand of door this is but the hinges have Lawrence USA on them.

Hi there, and Happy Holidays. I'm looking for a replacement bottom seal for my windows. I believe these are single hung windows (pic of full window attached). I searched everywhere on the window for the make/model, but I couldn't find any identifying markings. I have included two pics of the windows ... (cont.)

Hi, can you help me match this bottom weather seal? The tube is 3/8" diameter. My tilt windows don't have a brand on them but other parts match what you call Keller. Thanks, Paul

I want to replace my window channel seal. The seal has a 0.25" wide flange for sliding into the window groove. The height of the seal is difficult to measure as it has taken a set but is approximarely 0.25". The seal fits a 24" wide window. Pictures are attached.

hello i am in need some snap in glazing I'm sending you these pictures so hopefully you can identify what particular glazing i need maybe you have this type or something that will work in its place it is 3/8 wide I'm not sure of the measurement of the part that goes into the grove in the wi ... (cont.)

Vintage 1989 casements. Brand unknownspline is .25, bulb diameter is .25 as wellDepth of the kerf is .260 Weatherstrip is in the frame, not the sash Thanks