Viewing all customer Discussions for:

26-391 Slim Top Tilt Latch, RH

Measurements: 2 7/8 X 3/4 Need 4 left and 4 right side locks.

In search of these locks I need 20 thank you Thank you, Scott

I have Traco windows in my home and a part has broken. I wonder if you can help me find a replacement piece. I would like to order about a dozen (half RH/LH) if they are available. Attached is a picture of the piece I need to replace.

I am needing to replace these tilt window latches as part of an inspection to sell our home. Attached are the pictures of the current latches. They measure 3" long x 3/4" wide x 5/16" tall. The only markings on these current pieces is (.075).

says on bottom of tilt latch 5R and .075 down near end that retracts with it retracted says pat pending5,139,291 Latch is 2 7/8 inches long(main body) 3/4 inches wide

I require 4 LH and 4 RH latches as replacement to the one shown in the photo. What is the part # I should order and how do I replace them? Thank you, Jacob

I just purchased your 26-390 and 26-391. the only difference i just noticed is the tip that goes into the slot to keep the window secure is curved where the one I purchased is straight, measurements for the piece are correct. will the curved tip vs. straight tip make a difference? ... (cont.)

I would like to replace this part. I've included: 15L Patton: 5139291 that is inscribed on the part. The visible glass, 16x24, of the bottom section is broken, and needs to be replaced. Do you sell the entire window or the bottom half? Thank you for your assistance. Best, Hannah

Hello. I would like to order both left (shown) and right window latches.

2 5/8 inches long, 3/4 wide, and 5/16 deep. I'm having a difficult time locating this part. No name or number on the part or window.

This part stops the window from tilting in when open.

I need replacement for window locks in attached file. The larger window lock has part # of 536-B w/ a capital L (possibly for left side). The associated window has "DACO" inscription. I don't have any additional info for smaller lock.

I have a difficult time finding this replacement part. The window manufacturer is out of business. Do you have this part... The color is Beige/Bone color. Thanks Paul

The window/Latch is from a builder grade window from about 1994 or 1995. The dimensions on top are 2 5/8" X 3/4". My apologies for the pictures. I can get better ones if need be. Thanks, Greg

I have a few of these broken around my house, all the same. Do you have a replacement? if so, which model? I measured the latch to be just short of 3" long. Thanks. I was very glad to see you offer replacements. Have needed to fix these for years.

I have single hung vinyl tilt windows. I need to find both left and right hand latches that slide into a mortise that has been cut in the top of each lower sash. See pictures below. I am including pictures of a good latch. It is 27/8" long and 3/4" wide. I also need the left side window lock t ... (cont.)

Hi guys, I need surface release replacement mounts for Traco double hung windows series TR 4300; I took a picture of label,can mail it if needed but,rest of it goes as follows; 851771 062503 202-008 I appreciate your help and would like to order parts if you have them ASAP

Found the pictures and measurements very useful and have identified the part I am looking for but I only see it in white. I am looking for part number 26-390 (Left and right side) in ivory/light beige.

I had asked about replacements, in early July (case # 17425), and received a reply, from Tom .... instructing me to take photos of the broken part. I tried to send them today, but my e-mail was rejected, as addressee unknown. I have enclosed my 4 photos, below. I await your reply .... on my next ste ... (cont.)

Hi, I am in need of a tilt window latch 2 15/16" L x 1 3/4" w x 1/4"d. The brand of the window is not available. Thanks, Leslie