Viewing all customer Discussions for:

10-325 30" Shower Sweep With Drip Rail

I am looking to get a replacement seal for bottom of shower door. The shower door is a 24 3/4 inches. I may end up replacing the entire dripedge. The hinge on the door is on the right hand side when looking at door not sure if that matters. Please advise.

Need to see if you carry this type of shower door sweep that I can order. Please see photo. Thank you.

I am looking for a vinyl replacement shower door sweep. It is an angled "T" type. The top is .25 inches wide. I need a sweep length of 1.25 - 1.5 inches. Most I've found are only 7/8 inches

Does the top edge or backing need to have silicone applied for proper installation?

Can this item replace unitex tempered glass door original rail . Mine is leaking . Can you please show the installation instructions. Thanks -Peter

Would the shower sweep with drip rail (product code 10-325) work for a framed shower door (pictures attached)? The door is 26", but figured could cut. If not, any other suggestion?

Good Morning..... I'm currently at a job at Knob Hill condos in Manalapan and am looking for the above style rubber shower door sweep in a 30" length. I tried the local suppliers/Home Depot/Lowes, no one has this style sweep. Can you help? Or do I have to order new drip rails with the sweep? P ... (cont.)

I moved into my house last year and the shower is missing the drip rail. There are no holes for screws. What kind of drip rail should I get?

My shower door seal and drip rail is 25 1/4 in length, and does have three screw holes for mounting. The problem is, the side screw holes are three inches from each end and the middle screw hole is 12 1/2 inches from each end. I could cut the 30 inch sweep, but I don't think the screw holes would ... (cont.)

Need metal piece for bottom on shower door

Just wondering if this shower door sweeper can be installed by using the bath vinyl caulk to glue the sweeper onto the bottom of the door instead of using the screw. Thank you

The door is 27 inches wide and the existing metal piece is 26.5 inches wide.

Aluminum bar with rubber sweep. looks like your 30" shower door sweep with drip rail. bar is 27-1/2" long and 1" wide Has three mounting holes in bar, each end hole is 3-1/4" from the ends, the middle hole is 13-1/4" from the left end. it's off a folding shower door. I would have sent a picture ... (cont.)

I need a sweep with 1/8th inch round bead and 1 and 1/4 sweep. Do you carry anything like this????

My shower door has apparently never had a door sweep installed on it. I recall a plastic strip being there, but that came off years ago and I don't know how it was mounted. I don't see how a sweep would be installed since there are no holes for screws. The frame appears to be chrome or plastic. Not ... (cont.)

DO you have instructions on height positioning? i.e., how high, how low relative to the door frame the sweep has to go over or clear. (The previous install in my home was done where the sweep was folded under when the door was closed, so that it allowed water to go to the outside). How high is it po ... (cont.)

What part do you recommend to replace bottom of shower door Glass is 3/8 and length is 29 1/4

exactly how the shower drip rail is supposed to be properly sized and placed. For example, in the first picture (red circle), you can see one of my wife

Hi- I want to know if a door sweep you have would be available. I would like to replace the sweep and not the whole drip and sweep. Also, do you have double tape or do I need to purchase it at a hardware store. This drip was installed that way and there are no screws.

I have the 10-325 shower drip rail, with the black rubber seal. However, I'd like a more pliable contact strip. Can the clear vinyl 10-321 fit into the mounting channel on the 10-325?