Viewing all customer Discussions for:

Drawer & Cabinet

Foxwood dresser cherry Haverty SKU 5-4590-2244; Vendor is Pulaski ; model # 115702100 2 Pictures attached of dresser handles one broken off

Broken hinge on IXL cabinet

I know that it is a Malpa hinge but none of the numbers stamped on it come up when I search for them. I

Hello, I'm looking to replace 4 kitchen drawer track guides. The dimensions are 1 1/4 width at the widest then 13/16 width below that and 5/16 height. I also need 2 kitchen drawer trade guides with the dimensions of 1 1/4 width at the widest then 15/16 and the height is 3/16. I provided pictur ... (cont.)

20 year old cabinets. One drawer was exposed to water and drawer slide on one side is rusted. Pictures are of: 1.) drawer slide piece that attaches to drawer itself. Mate of the piece that is rusted. 2.) image of how the part not attached to the drawer attaches to the back of the cabinet. 3. ... (cont.)

I need to replace a Mepla ACC 140-130 degree face frame hinge. The number on it is 698.243.5900

I need to replace the small round piece of hardware in the picture. The handle is fine. Thanks, Cindy

Name on guide is Ronthor Reiss Corp NYC. Part R-40-28. Patent No. 3.201.187. Everything I find locally won

The guy I bought the cabinet from told me they came out of a pharmacy. I purchased part 10-101 which is the right size 7/8" x 1/4" with the hole size of 3/8". I drilled out the bearing but the problem with the 10-101 is the center after I removed the bearings was thin and broke when I tried to put i ... (cont.)

I found that these are all beginning to break or have already broken there

We need to replace cabinet door hinges. The portion that attaches to the cabinet door is 2 & 3/4 inches wide. The screw hole slots on that piece are approximately 2 inches on center. The indentation portion that goes into the door measures about 7/8 inch wide by 1 & 1/4 inches long. The portion ... (cont.)

Have R-way dresser and need drawer slide for metal bracket slider. Can I use 1 5/16 bracket? This piece was bought in 1951. Should I order 32-032 or 32-088.

Part Number G 6601. White plastic sliding drawer bracket. Dimensions: 1.75 inches x 1.125 inches x 0.875 inches. Cabinet and drawers purchased from Manor House in Pittsburgh, PA by contractors. Would appreciate any help you could give me. Richard Orr

Trying to identify part for purchase - from under drawer rail in kitchen cabinet This is from a single rail mounted in the center of the drawer. There is a track in the cabinet which the track under the drawer glides along. The plastic "sledge" in the picture is like a short "T". The rail ... (cont.)

Help please!! My mom is 87 and disabled and her aides pretty much ruined her kitchen. I need a plastic drawer stop (it broke off rear of cabinet drawer). Please see photo attached. Any help to find a replacement part? Mom lives on social security on very limited income. Any help would greatly be ... (cont.)

The small circular plastic piece at the front of the bottom of the dresser (where the drawer slides in) broke. The other one is still there. The drawer does not fit properly. I think it is like a tack with a nail attached to it. It's brown. Let me know if you need a picture. Thank you! ... (cont.)

Hi there. I need to replace a couple of drawer guides. Because the guides are chipped it's difficult for the drawers to slide in & out. They measure 2 5/8 in wide and 2 1/2 in in height. They are on a R-Way bureau manufactured in the late 1950's. The guides themselves have no markings or numbers on ... (cont.)

does this clip come in brown

I have searched all over and have struck out in finding drawer slide rear mounting brackets that even closely resemble the two attached photos. Can you help? The square opening that receives the drawer slide measures 5/8" by 5/8" square. The "T" slit at the top measures just under an inch across. T ... (cont.)

Hi- We went to Home Depot to see if they would have the replacement part to our kitchen cabinet drawer part that broke. It