Viewing all customer Discussions for:

Drawer & Cabinet

Looking for replacement rear receiver brackets like the one shown here. The guides on both the drawer and the cabinet do not have any names/codes that I can see. The guide that goes into this bracket is about 1

Part is marked with V 41, and US pat Re 32 134.

Drawer pull #32-122 is not correct for our need. The dimensions are somewhat different. The old one is numbered #452 from Hardware Designers. glide width 1 9/16" - total width 2 1/2" glide height 3/16" screwhole from top of glide space 3/4", from bottom 1/2", from outside edge 3/8" ... (cont.)

I need a couple of guide boots or rear sockets for a drawer slide. It is 3/8 deep and 7/8 wide.

Dear Sir / Madame: Attached is a photo of a bottom drawer slide socket, which is damaged, and what I believe is an 18" Liberty drawer slide. Would you carry a pair of replacement sockets that I can use as a replacement? The lip won't old the slide anymore since part of it broke off. Thank you ... (cont.)

Hello, I have a kitchen garbage slide out that is broken. It is labelled Unigrass 6000. My troubles started when the small plastic piece broke (2 pictures of it). The remaining pictures are of the drawer slides and the garbage slide holder. I think I would be okay if I just replaced the small pl ... (cont.)

The wheel on the cabinet no longer works. Took apart and bearings fell out. It is 20yrs old. What is it? What make? Lowes and Home Depot do not have it. Please get back to us. Length 22 inches Wheel was 7/8? Estimate. Thank you.

I received a dresser from my son that he was no longer using. I don't know the brand but noticed it has Ronthor back stops and the guides may me Ronther also.I can't seem to find guides with the rollers in Sioux City. Any ideas will be appreciated. I'm not the most accurate measurer at times but hav ... (cont.)

Do you have a replacement part for this? Thank you

Hello,I'm in need of several nylon rollers & retainers for my Steelcase desk. Rollers are 3/4" o.d.,5/16" wide,approx. 1/4"dia. thru. It has a 1/2"dia.x 3/32" deep counter bore on one side & an o-ring groove that is off center. Thanks!! Joe

I need a rear drawer guide just like the one posted to replace the broken one I have. Was told to order #4312544 through Sisco. However, notice your measurements may be different than I have. It looks like my track opening measures 1 1/4". Is this going to work. The name on my rear drawer guide ... (cont.)

Do the 32 335 hinges have soft close, or is a damper available? I am using these on steel cabinet doors where the 35mm bore is not possible. Thanks!

I am searching for a match to this 3 1/2" Thomasville brass drawer pull that is attached to a set I purchased in 1992. i am looking for 10 of these.

I need to replace several plastic drawer glides that are on my parent's very old cabinets. The current plastic glides say Hardware Designers Inc, So Hack, NJ USA. I did not think to measure the width of the metal glide rail, and the plastic glide is broken. opening on the plastic glide is about 1 ... (cont.)

This is for a stove drawer. It has rivet type but I would prefer to replace with a bolt style.

Hi. I have bedroom furniture ( Vaughan- Bassett) and I am in need of some drawer guides. item # 820-002-401. M20-Runners/Guides split . My furniture has been discontinued by the manufacturer and I was wondering if you could find some guides that are adaptable. I would like to order a dozen if y ... (cont.)

Are the holes 2 inches apart (center to Center) 32-345 product?

You had offered another bracket in this link: Larger shelf bracket needed : SWISCO.com discussions/Larger-shelf-bracket-needed-77-63347 I received my order today of (12) 32-313 : Shelf Brackets, but unfortunately, I did not order the right item. but I think I am going to end up with the same ... (cont.)

Hello, I have some cabinet drawers that need replacement wheels. The cabinet maker is St. Charles and it was installed in 1964. The following are 2 photo of both sides of the wheel. They measure 1 inch. Thank you for your assistance, please let me know if you have any questions.