Viewing all customer Discussions for:

58-055 9/32" Bubble Seal With Angled Base, 25ft

I need to replace the weather stripping on all of the windows in a house built in 1994. The windows are Marvin casement windows. Please see attached photos. Do you have replacement WS that might work? Thanks in advance.

I have casement windows I'm not sure what brand it says truth on the hardware. I would like to replace the bad weather stripping and don't see an exact match on your website. Do you have any suggestions on which is the best replacement. The 58-053 has the barbed but not 2nd trim/clip piece. 58-164 ... (cont.)

I have a pella sliding door that was installed in 1968 that needs an inner panel weather strip. Is there one still available.

Looking for a bubble weatherstrip that would work in the customer's storm doors. I have looked at available weatherstrip, but haven't seen a match. Maybe you have some more insight into something that could work as a replacement. Thanks in advance! -Joe

We're back. We have moved to another house that has Wenco Casement Windows and are looking for weather stripping. The windows are from 1993. I did see someone else here with the same windows but 1992 and our weather stripping doesn't match theirs. I've attached a picture I hope it gives you enough i ... (cont.)

I have many Milgard casement windows that needs weather stripping replaced. Need to find out which part I need to get. Millard Woodclad series Thanks

It's looks like your part # 58-055. Would you agree?

Hello, I'm looking for windows sash and windows sealing. I don't know the windows name but I think its Anderson. build in 1990. windows weatherstrip it look like hard plastic between a piece of wood the the side of windows.please help.... Last week I got the weaterstrip part 58-053 it worked for ... (cont.)

Struggling to find replacement weatherstripping(WS) for older home windows. Can't ID mfr of window. WS slides into a channel, and is not quite bubble type as is connected to both sides of top edge(~ .25" wide). Length of base extension is ~ .25" ... height of pseudo bubble ~ .3". Perhaps bubble ... (cont.)

I am trying to replace the Wool pile and kerf mount bubble. I believe I have the correct ones. My next problem is the bottom weather strip. Attached is pictures of the weatherstrip, the part that fits in the groove also shown is 3/16. Since I am unable to locate on website, is possible for a sub t ... (cont.)

I need replacement weatherstriping for 2 casement windows

I am looking to replace the weather stripping on my Crestline windows that were manufactured in 1994, having trouble finding the exact weather stripping needed. Can you assist? Jeff

Can you help with finding a replacement seal?

Need to replace weatherstripping Thank you!

Hello, I am searching for replacement. This weatherstrip came out of a Norco casement window. Thanks for any help, Ed

I have 1983 Weathershield wood casement windows, for which I need to replace the weatherstripping. The head and side weatherstripping is hard to find as it has a dual kerf with a half bubble on top. Please see attached pictures where the half bubble is missing.

this weather stripping was in a wood window manufactured by Willmar. the bubble has two small ribs/fins. The weather stripping slots in place in two grooves in the window frame, one for the barbed kerf and one shallower groove for the "front edge" on the right side in the photo.. ... (cont.)

I am looking to replace the window seals/weather stripping and although the picture is not too clear, there are two slots in the window for the bulb seal to be inserted, one is a barbed/kerf and the other (outer) angle smaller slot.

Window seal from pella proline window. Needs to be replaced. What do you to recommend.

I need some help figuring out the seal in question. I found the bubble seal on your site to order but not the one that has the bubble and the other angle. On the post-it note the dimensions are on the right. House built in 1995 and everything we can see is that they are Weather Shield. Thanks, Mik ... (cont.)