Viewing all customer Discussions for:

58-055 9/32" Bubble Seal With Angled Base, 25ft

I'm having a tough time finding these. Any help would be appreciated. Thanks.

Hello, I'm looking to replace gaskets for Biltbest double hung windows. Windows were made/installed approx 1994. Any help would be appreciated. Brian

The door does not have existing stripping so I can't show you sample. There is a slot around the frame but not on the usual face but on the side of the frame. Also the slot is ~1/16" wide vs normal 1/8" slot. It is 1/4" deep. I have attached images and a sketch. Thanks Richard

Home built in 1993. Both Crestline double hung and casement windows -- all aluminum clad Found a number on one of the double-hung: 120193Y27B3M (hard to read) Could not find any on a casement -- these get more sun and I'm guessing the ink degrades over time. Looking to replace the gasket ... (cont.)

Jeld Win casement window bubble seal. Looks like it might match up to 58-183, but bubble looks a little small in comparison. Looking for a suggestion. Thank you, Tate

This is a cross-section of weather striping on a vinyl casement window. It is kerf set. the kerf edge approximates 1/4 inch long and 1/16 thick. Half round "bubble" is 1/4 inch wide, 1/8 inch high. the "wing" is approx 3/8 in length. I know you may not have an exact match but do you have some ... (cont.)

Some other details: - ~1/4" in diameter (compressed from window being closed, distorted slightly from thick layers of paint) - vinyl (?) covered foam bulb with plastic base, base is shaped like a "T" The horizontal (top) cross of the "T:" - one half has two clear flexible "fins" pointing inwar ... (cont.)

We believe this was on the frame, opposite the hinge.

Here's a better photo of the weather stripping in need that goes into a tight channel at the bottom of the sash. I can't seem to find one that looks like this. Any help you can give would be greatly appreciated.

This is the outer seal on a crank type window with wood casement. The concave tip comes in contact with the edge of the window and is supported with a thin rubber strip on either side connecting to the molded plastic base. Any help in identifying this strip or providing a possible replacement wou ... (cont.)

Do you have this weather stripping?

Do you have a bubble seal to replace this? 5/16".

I have weather shield windows and i have the attached weatherstrip that I am not able to buy anywhere. Please help me find the similar or equivalent weather strip. Thanks, Naren

See if you can match with your stock supply.

Hello Swisco experts, You helped me find window cranks for a bay window. Now I need weatherstripping for the same bay window. It is similar, tho' not identical to Offset-T-Slot-Foam-Filled-Bulb/pd/Bubble-Seal/58-171 or Bubble-Seal-9_32-inch/pd/Bubble-Seal/58-055 Any ideas about which would work ... (cont.)

The problem is the window sill is bowed and I need a bubble seal with a larger diameter than 5/16", possibly in the neighborhood of 9/16". The problem is that the sill has bowed in the center, thus I need the seal to work the entire width of the window sash. Your product 58-053 looks similar to wha ... (cont.)

This weather stripping has an edge that presses into the wood around the windows allowing it to be held in place securely. The round part of the weather stripping is about 1/4" dia. Nearly all the weather stripping along our house windows is cracked, broken or partly missing. Although I could ... (cont.)

I tried contacting you a few weeks back, but no response. trying this again. Please let me know what you have that might work.

Any idea what I can use for this? It's a vinyl glazing strip from 1983 Pozzi wood casement windows.

Hi, I would like to get the correct part to replace weather stripping on my casement windows. I think the manufacturer is HUNT. Attached is a pic. The L section is 1/4 of an inch on either side, with one small groove/spike to hold it to the window. The bubble is also around a 1/4 inc ... (cont.)