Viewing all customer Discussions for:

70-180 Storm Door Insert Clip

I have this on my storm door holding glass in. I am trying to find replacement strips. Thanks.

Hello, Do you have this type of snap in glazing? Thank you, Junior's Painting Roger

I have a Wright metal storm door/screen combo whose retainer strips were always a bear and now don't work and are an old design. It used to work by squeezing one side of it into a 6 mm gap in the frame parallel to the insert ,on the inside, with the remainder lapping over the insert. The replacem ... (cont.)

looking for long plastic pieces the lenght of glass & screen also clips - don't know what the long pieces would be called , ours are hard & brittle & breaking off

Looking for replacement retainer for storm door window. Can't find name or serial # . Had a wright brand door handle . House built in 1999 sandstone color full glass storm door.

Snap in piece on the sides of the removable glass/screen on a storm door. It's about 7/8" x 1/4".

The part we are looking for holds the glass in the doors and sides of our china cabinet. It is "L" shaped with a screw hole for a #6 (approx) screw. It is approx 3/4" long, 1/2" tall, and 1/2" wide. Pictures are included. If you have these we need 30 of them, and just about all of them in the ca ... (cont.)

The door has a pella sticker reading 031307 9056133145 I have another door very similar but the sticker reads 080405 90563 7586 Both appear to use the same bead

These are plastic clips that hold the glass in the storm door. I need to replace four that have broken

I am looking for replacement strips for my glass/screen storm door. I can't find a brand name anywhere on the door. I am enclosing photos of the strip. Help! ?

Hi- I have a Cole Sewell storm door, which I'm just finding out do not exist any more. The glass portion of this door has been held in place by 4 pieces of weatherstripping. 3 of the 4 have warped due to the heat from the sun and would no longer stay in place. The 4th piece was holding it OK, but we ... (cont.)

Need replacement door spline. I think it's a Larson door. It was long strips but they were so brittle this is all that's left Thank you Kathye

I am looking for the vinl strips that hold the glass and screen into my storm door The storm door is Cole Sewell reg #10219994539 0022 Can you recommend the replacement part for this?

I am trying to find replacement snap in glazing for a screen/glass door. I do not know make or model and do not have a piece of the old glazing. The door has a interchangeable screen or glass panel. The dimension of the glazing channel is. 9/32 tall 1/4 deep And a 1/8 step down to t ... (cont.)

I am trying to replace the retaining strips on my storm door. It is an old door and I do not know the manufacturer. There are no markings on the door or frame that indicate a manufacturer. Please refer to attached PDF for a sketch of the strip. Thank you for your help. Mark

Do u have o chart w x sections of plastic retainer strips for storm doors?

The strips I am trying to replace hold both the storm window and screen. I remove them twice a year to put in the window in the windter and the screen in the summer. Two Strips are 29". Two strips are 73". End dimentions are side 1 - 5/16 top - 1/2

Looking for the plastic piece that holds the window and screen in p;ace in a storm door. Picture attached with a dime under it. It's a Sears storm door model #656. I need 4 pieces (for two storm doors) 41 1/2 inches long.

i am interested in a storm door panel clip similiar to your 70-180, but with these dimensions: 3/4 in wide and 1 inch long with only one side off set by 1/4 in. please let me know if you have that size and what would be the cost. i believe that this is for a cole sewell storm door. ... (cont.)

Hi, Looking to find parts to hold the glass panel for the storm door.