Viewing all customer Discussions for:

32-089 Drawer Track Back Plate, Pair

Hello, I need to replace the rear mount drawer sockets on many of my cabinets. They are cheap and do not hold up against my children. I measured and the opening for the slide needs to be 1" and the socket needs to be at least 4" long. Can you please guide me to the right one. I ordered replacemen ... (cont.)

Here is a picture of my slide socket. If you make the picture bigger you might be able to read the part number 6050.

What size is the bracket? part #32-089 Thanks

The only identifying number stamped is 60.1890, the rail measures 1" high x 3/8" wide. I ordered your #32-089 per one of your posts. The set I received is white, and will accept per its inside measurements a rail that is 7/8" high x 3/8" wide. Did I receive the wrong part or is this not the part num ... (cont.)

Like others who have posted, I cannot seem to find the correct size drawer socket. I have the old plastic brackets that have now dried out and are cracking. The inside dimensions of the socket are 3/8" by 1-1/8". The overall length is 2-5/8". The dimension I cannot seem to find is the 1-1/8" for ... (cont.)

It has "R1" stamped on it. The dowels/pins fit into holes in the back of the cabinet.

Do you have this part 4 1/4 " length? Thats the length pf me pesent part Im concerned the 31/4 may not hold. Thanks.

Can you please help with replacement rear drawer brackets that have the dimensions set forth on attached phtotos. I do not know the make of the cabinets.

The number on the socket is 6000100200 it measures 3" long x 1 1/4 " wide and the opening is 1". Do you carry this item or a comparable replacement? Thank you

In reference to my order listed above, it appears that I ordered the incorrect socket sizes. The sizes required are s few inches bigger than what I ordered ordered. Please see the attached photos. Providing measurements has been somewhat of a challenged for me as I've been unable to measure to wh ... (cont.)

Could you point me to the proper replacement part for my decorite drawer slide socket? Mounted it's 2.5 inches high and 3.5 inches long. The slide is 1 inch. See photo. Thank you!

I have been looking for a replacement part for my kitchen drawer. The plastic socket is 3 3/4 inches long and the local hardware stores only carry a part that is shorter than this. I am hoping that you can help me find the correct part. Thank you, Sue

The attached pictures are belong to the original part. Its the "side mount & bottom mount drawer slide mount socket". Inprinted on the bottom is "ADAR 8 LEFT". It is 3 and 3/4 inches long. I found a replacement part but it does not last and breaks easily because it is shorter and does not s ... (cont.)

On the back plate there is a capital letter "R" and the number "60.1890" OR "50.1890" (very small and hard to read). Length (height in the photo) is just under 2.5" It fits 1" tall x 3/8" wide drawer track. I think this part: drawer-track-bracket/pd/Replacement-Drawer-Sockets/32- ... (cont.)

1 1/4 inch opening

We are looking for some of these drawer glide supports. Is something like this still available?

the receiving slot is 1" tall and 5/16 wide. The overall length is 2.4". The mounting surface is 1" x 2 1/2" There is a logo on it that looks like a "W" but not excatly. i could not get a clear picture of the logo.

bath room cabinet drawer slider bracket Bottom:1" top 1&3/8 grove:3/8 hight:9/16 thank you

Picture 1 shows the right rear drawer track socket in use. Pictures 2-5 show the broken left socket that I need to replace. The metal drawer slide is 7/8" high. The only identifying mark I can find is the number 60.1890 on the end.

Hello, Looking for replacement parts for L&R rear kitchen cabinet rear slide brackets. Bracket is about 3.5" long from top of base. Base is 1 1/4" wide by 2 1/4". Only marks on the parts are on plate. Says "G*" and 6050 on both L and R versions. There are 4 slits for screwing the bracket into ... (cont.)