Viewing all customer Discussions for:

26-241 Pivot Bar, 3"

Window is general aluminium 7000 series. Do you carry this part?

I am trying to locate pivot bars for a vinyl window that tilts inward. The sash locks have the "Carefree" wording on them. Do you carry this replacement part?

pin #26-241 is the same as i have but the end part with the locking t has only one tab mine has two will this one work

Hello, I need to replace a couple of pivot bars on my windows. My bar almost matches your part 26-241. The only difference seems to be that the screw hole on my bar is at 1.5 inches. I seem to have some room in the window frame to extend the bar into the frame but not quite 1/4 inch. There are no ... (cont.)

ONE PICTURE IS OF BROKEN PART AND ONE IS NOT BROKEN. THIS IS THE PART THAT THE PIVOT ROD AT THE BOTTOM OF THE WINDOW INSERTS INTO WHICH I ALSO NEED. I WAS HOPING YOU COULD DETERMINE WHICH PIVOT ROD I HAVE ALSO. I CAN GET THAT INFO LATER IF NEEDED. I WILL ALSO NEED THE SPRING CYLINDER BUT WAS U ... (cont.)

I am finishing a job someone else started. They have already purchased the 15-129 pivot shoe. However, I need to replace the pivot bars as well. My question: will the 26-316 pivot bar work with the 15-129 pivot shoe? Thanks - Donald

Looking to replace several pivot shoes that have deteriorated and broken apart (see attached photos of an intact pivot shoe). I have already identified the associated Pivot Bar part number and installed them as replacements (they work great, except, of course, in the windows with failed pivot sho ... (cont.)

Trying to find a replacement part for this pivot lock shoe. It appears that it works with Pivot Part Number 26-241. Its about 1 inch in width. Any help would be appreciated.

We purchased BetterBilt windows (series 350) with removal sash in 2006. I have a broken pivot bar and it looks like 26-378 or 26-241 may work. What is your opinion on which if either will work for me?

This is from a 1997 CertainTeed Carefree window on our doublewide. Need 2 of these one for each side.

Looking for replacement carriers for my windows. I upload a picture of the spring (which is fine) & the broken carrier which is 3 inches long and about 1/4 wide. I can find no identification on the windows, springs or carriers

Hello, Need help to properly identify this part before ordering... Any help is appreciated. Here are the camera shots of the pivot bar.... -shawn

Hi, Thanks in Advance, I have attached the right side and left side -which is broken and need your help in locating the part for me. Praveen

I would like to identify and order 6 pair of left and right pivots which have all snapped at the same hole. I do not see them at your site and have no part numbers or even manufacturer. I have attached a couple of photos. The dimensions appear to me to be 3 in long by either 9/32 or 5/16 wide and 3/ ... (cont.)

I am trying to replace the item missing in picture 2261 with a part like the one in 2260.

Will pivot bar 26-241 and pivot shoe 15-135 work together?

In the first and second picture, I need a coil balance shoe that that is 1-1/2" tall, 1-1/4" wide, 1/2" thick. I couldn't find any stamped numbers. In the Third picture, I need the 3" T Bar Pivot with the exact hole placements. From the bottom to the center of the hole closest to the T-end is 1-5 ... (cont.)

Your Pivot Bar, 3" Product Code: 26-241 HAS THE CORRECT DIMENSIONS that I need. But I need a T-nose end not rounded end. I have ballast Pt530CSB. Do you have the pivot bar for that one similar. Or can I replace the ballast and the pivot bar with a a different one.

I am looking for the aluminum pivot for a double hung Certainteed window. I am not sure exactly when the window was made but the house it is in was built 11 years ago. The part measures 2.5 x 1 inch not including the extended pivot which is slightly more than 3/4 inch. It is basically a right ... (cont.)

I need Pivot Bars,shoes with the coil included. photos attached.