Viewing all customer Discussions for:

32-062 23-5/8" Self-Closing Drawer Slide Pair

Hi there,From other posts, I'm thinking these plastic clips with pegs are nearly impossible to find. The pegs broke for one drawer, so now the rail won't attach to the back of the cabinet. I'm guessing I'll need to reinforce the back with wood and find a new rail system with screw-in back mounts. An ... (cont.)

Hi,I have a cabinet drawer rail from 1985. There are not markings listed. The rail it sits on is 22.5 inches from the very back to the very front. The top part that rolls across it is 21 inches. It sits very flat to the cabinet around it (not much spare room is needed around the drawer for it to sli ... (cont.)

Good afternoon, We are looking for replacement drawer slides for the attached pictures. The one glide shows #PMI-CM565L. Are you able to quote?

I need to replace the actual drawer but the drawer slide and bracket need replacing as well. Can you help find the parts or suggest something similar/better? The bracket is cream/off-white and holds the drawer slide at a 90 degree angle. The bracket has plastic tabs on the back that holds onto the ... (cont.)

I need a replacement slider for a Merillat cabinet drawer as shown in pics. The slider wheel is worn out. Thanks

The cabinets were installed in 1992 by the previous owner so I do not know the manufacture. The inside dimensions of the socket are 3/8 by 15/16 and 1 1/4 deep. The exact replacement would of course be best, but if there is one that requires screw mounting with everything else correct then that wo ... (cont.)

I am looking for a replacement for a UNIGRASS 6600 drawer slides. The cabinet mounted rail is approx 23&1/4". The drawer slide is approx 22&7/16". The measured width of the slide is approx 1". Distance between the two cabinet mounting locations is 20&7/8". Markings on the Slides UNIGRASS 6600 ... (cont.)

This piece broke today. Need a replacement. The area to insert the railing is 1.5 inches tall by 1/2 inches wide. It slides to adjust. It is attached to the mount, which is 2 inches wide and 2 1/4 inches wide.

need 3 sets. Side mount. The outside metal circular tabs fit into metal frames installed inside the cabinet. Cainets installed 25-30 years ago.

track back plate has broken so there is no suport for the side rail. I think maybe I need 32-089? My side rail is 1" wide. The back plate is broken in a couple of drawers--1 is a kitchen utensil drawer that is about 22" deep and other is a desk drawer that is about 16" deep but except for the len ... (cont.)

Looking for p/n for a rear press-in drawer slide mount (plastic piece) as seen above in the picture.

I want the rail that your part #32 040 goes in

I need the left drawer guide for a 22 inch drawer

Greetings, I found your website by trolling for pictures of bottom mounted drawer slides like the one I am looking for. you had a picture just like the one I seek but it's not a slide currently listed in your on-line parts catalog. This is your link to that picture:https://www.swisco.com/images/pi ... (cont.)

Hello I am looking for the above brackets used in the kitchen cabinet drawer slide support. Attached are front and back faces of the bracket. Would appreciate if you could assist in finding the same.

Hello: One of our kitchen cabinet pantry's drawers fell and saw that its rear bracket for the drawer slide was broken. Was looking to see if you have this bracket. The attached 2 pictures show the broken one & a working one. Looking forward to hearing from you. Thanks

Part is broken (both sides) Mounts to back of cabinet.

I am looking for a drawer socket for a Scheirich PPW098 88. This socket slides on a metal anchor strip that is screwed into the back of the cabinet.

That plastic/nylon piece attached at the rear of the cabinet that the rail attaches to.

I am looking for this specific Side Rail Holder. Please let me know if you carry them.