Viewing all customer Discussions for:

32-062 23-5/8" Self-Closing Drawer Slide Pair

The plastic/urethane end of the right drawer bracket cracked into three pieces. I need a replacement part or the entire bracket assembly. Best I can tell the whole assembly number is 00045-51, 6603/582/cl-cr/AI. Stamped into plastic/urethane end bracket Pat# 4930739. I tried to include a picture of ... (cont.)

I have a part number as 2883164 from Merillat Replacement guide con kit base

I can't find this. It's the rear slide mount. The photo is missing one of the plugs that goes into the back of the drawer slides.

Hi, I'm looking for a drawer slide for a 24 inch drawer that goes into a rear drawer socket that is pictured in the upload picture. The back of the drawer slide has a 90 degree bend that slides into the rear drawer socket before mounting the screw in the front of the drawer.

I have a grass slide labeled a unigrass6600. It is of two unequal lengths. The drawer mounted piece is 19 3/4". The piece that is mounted to the cabinet and the rear is 22 7/8". Do you carry a slide like this. Thank you Rich

Looking for guide that fits ~1 1/8" slide.

Good Morning, The Unigrass item I need is shown in the attached photos. Please help me order two of the brackets along with the plastic back wall mount. Thank you very much

Hello. I believe the slides are made by Grass America and might be the Express model. These came with the kitchen cabinets that were installed in our home in 2013. The rear bracket has broken on this one and we're looking for the replacement for these parts. The slide has a 90 degree angle where ... (cont.)

Hello! do you have a replacement suggestion for thee cabinet sliders? As you can see in the picture, the wheel is coming off and Houck does not make the part anymore. I am comfortable changing both sides to a new set, and the back plate is fine....thank you!Attached two pictures.Donna ... (cont.)

I need the plastic replacement for the back of a 23-inch side glide kitchen drawer. I've attached the photos of the one that will fit. Do you have these, and if not, is there something else that would work thank you.

Hello. This piece broke off of the back of the kitchen cabinet. It looks like it needs the two prongs. I've attached one of the brackets which still has the prongs attached.

That green thing holding it was just so that it wouldn't fall. I can't find this anywhere. Where can I buy this rear drawer bracket?

Looking for drawer glide replacement. Measures 23-1/4" long, the rail is 1" high and 3/8" deep. The only marking I could find is the letter "G"

The only markings seen are Unigrass 6600 One of these on the drawer is bent near the roller and needs replacing

Hi there,From other posts, I'm thinking these plastic clips with pegs are nearly impossible to find. The pegs broke for one drawer, so now the rail won't attach to the back of the cabinet. I'm guessing I'll need to reinforce the back with wood and find a new rail system with screw-in back mounts. An ... (cont.)

Hi,I have a cabinet drawer rail from 1985. There are not markings listed. The rail it sits on is 22.5 inches from the very back to the very front. The top part that rolls across it is 21 inches. It sits very flat to the cabinet around it (not much spare room is needed around the drawer for it to sli ... (cont.)

Good afternoon, We are looking for replacement drawer slides for the attached pictures. The one glide shows #PMI-CM565L. Are you able to quote?

I need to replace the actual drawer but the drawer slide and bracket need replacing as well. Can you help find the parts or suggest something similar/better? The bracket is cream/off-white and holds the drawer slide at a 90 degree angle. The bracket has plastic tabs on the back that holds onto the ... (cont.)

I need a replacement slider for a Merillat cabinet drawer as shown in pics. The slider wheel is worn out. Thanks

The cabinets were installed in 1992 by the previous owner so I do not know the manufacture. The inside dimensions of the socket are 3/8 by 15/16 and 1 1/4 deep. The exact replacement would of course be best, but if there is one that requires screw mounting with everything else correct then that wo ... (cont.)