Viewing all customer Discussions for:

Drawer & Cabinet

Looking for a replacement

THIS IS A PLASTIC REAR MOUNTING BRACKET FOR A SIDEMOUNT GUIDE USED BY MIDCONTINENT CABINETRY BETWEEN 2011-2013. THESE ARE NO LONGER BEING USED AND NO ONE SEEMS TO BE ABLE TO TELL ME WHO THE MANUFACTURER WAS OR IF THERE EVEN STILL BEING MADE. i SURE HOPE YOU CAN HELP.....THIS REPLACEMENT ISSUE HA ... (cont.)

hi, i am looking for this drawer slider socket. i saw one on your website by the dimensions dont match to the one i am looking for. the dimensions for he bracket i need are in the picture attached. please let me know ASAP.

Hello, I'm looking for a Unigrass 6600 (stampe in the slide) bottom mount drawer slide for a 22 inch drawer. Pictures attached.... The slide measures 22 1/2" long and the cabinet mounted slide has a 90 deg bend at the back that mounts directly to the cabinet back, eliminating the plastic mount th ... (cont.)

I have Merillat Cabinets 1970

I need to replace this part from my kitchen cabinet drawers. They are on the side of the drawer and hold the drawer in place. With one peice broken on the side, the drawer is crockid. Thanks!

Please reply as to availability of bracket as described. There are no markings, etc. Thanks, JoAnn

pictured is the right side bracket and support. We would like both left and right replacements (6 of each) of the plastic piece (which inserts into back of the cabinet) width of metal bracket is 1 inch. length of plastic piece (full) is 2 1/8 inches. width at widest point is 1 3/4 inches. hei ... (cont.)

Top part is broke off. It's about 41/2"long

Hello, I need to replace the rear mount drawer sockets on many of my cabinets. They are cheap and do not hold up against my children. I measured and the opening for the slide needs to be 1" and the socket needs to be at least 4" long. Can you please guide me to the right one. I ordered replacemen ... (cont.)

Please help! Hinges inadvertently thrown away during kitchen installation. Sister cabinet has same hinges. Stamped DFC. Diameter of recessed hole is1 3/8", depth is 7/16". Screw holes just shy of 2" apart. Need to obtain quickly. House went under contract in less than 24 hours. Inspection on W ... (cont.)

Hi, this seems to be a hanging slider socket. The end part broke, so I am trying to find a replacement. Please assist. THank you.

Hi, Can you supply some slide drawer brackets? Thanks! Joe G

G'day guys, I recently acquired a nice solid timber side board with 3 drawers. The guides on the back are broken and I need 3 but will be ordering 6 as a just in case for later. As we don't seem to stock these in Australia, could you tell me the closest match to the attached photo. Yes we work in ... (cont.)

I have rear rail bracket with a part number of P5850-23 and P58590-25 nd am looking for replacements. Your part number 32-012 looks like it. Please let me know if I'm correct as I would like to order replacements. Thanks Jim

I am sending you 3 photos. 1- shows roller and end cap missing, but you can see the spacer. 2-roller on stem but has lost the ball bearings. 3- end cap keeping roller on stem/spacer. The roller is either 7/8 or 3//4 inch. I forgot to measure it exactly. Thank you Martin

Hi: Looked at 3 pics of roller 32-039: How does it stay in the drawer hole? Also, regarding a different drawer roller 32-096: what's the diameter of that metal piece between the nylon wheel and the threaded piece. Thanks for any help. Nelson

Here is a picture of my slide socket. If you make the picture bigger you might be able to read the part number 6050.

Is there an adjustment screw to vary the closing mechanism or is that not needed?

I need replacement drawer glide locks. These are approximately 1.75 X 3.75 inches. Installed with the cabinets around 2006.