Viewing all customer Discussions for:

Drawer & Cabinet

This part catches underneath the drawer so it does not fall out

Thomasville Impressions Bedroom Furniture. Plastic guide on the front of the drawer slide rail. I would like to get 6 of these parts. My name is Les

Have you seen the attached drawer guide? I am having a hard time finding them. We need one on each side of the drawer as a support. Our condo was built mid-70s so that would be the vintage. Thanks

I have a 9 drawer dresser with at least 3 broken drawer glides labeled Reiss MFG CORP R-25 patent pending. Can you provide me with replacements? Since 2 broke in one week I should probably buy all nine now. Thanks Marsha

Hopefully you can help I have Vaughan Bassett model 715-115 chest of drawers. I did not see the 32-81 the 32-76 looks similar,maybe you can tell by the brand and model number exactly what part is required.Thanks for your help.

I am restoring an old metal cabinet for a sink. The cabinet has 3 drawers and I need to replace the rollers. The exterior diameter of the roller measures 1 1/8"; the interior hole measures 3/8"; the roller is 1/4" thick. Do you carry a similar sized roller? I need 12. Thank you for your help! ... (cont.)

I have purchased some Kenlin parts from you in the past. Attached are two photos of drawer slides that are used on that same furniture. The slides or round discs are slightly thicker than a quarter and almost exactly 1" in diameter. Do you sell such an item? I could not find it on your website. ... (cont.)

I ordered this product in hopes that it would replace a 1980's era American cabinent drawer bracket. The dimensions listed were close to what I had, so I gave it a shot. Turns out the new bracket fits better than the original equipment bracket. And much beefier. I am very pleased. Attached are pic ... (cont.)

I also have Homecrest cabinets that has a small white plastic piece that has broken and the cabinets will not stay closed. I am looking for replacement hinges.

No obvious markings except Made in USA and Amerock Thank you. Terri

Can you tell me the screw size, e.g. #6 or ?, for the Clear Corner Brace 32-093? Thx

Somme of my cabinets do not close all the way. I'm thinking that replacing the hinges may help. Please see if you can match the hinge and think this may work. Thank Mike

Hi. I'm looking for a replacement part for an 18" grant sliderite. Thanks, Jules

Is this bracket available? My "poor" Little draw is setting on my kitchen table. S o any information you can give me will be appreciated. I have been to 5 different hardware strores, and looks like nothing will fit. And, if you have store here in Omaha, Nebraska., would be much appreciated to kno ... (cont.)

I'm looking for ball-bearing rollers for kitchen drawers made by Wood-Mode, probably installed in the 1970s. The only marking on the roller is the numeral 3 on the face of the nylon wheel. The small post fits into a hole in the glide, then is flattened with a hammer to hold the roller to the glide. ... (cont.)

Rear dresser draw glide 2857233

This appears to be a match, however can you give measurements of distance the 2 holes are from the edge (where in the picture of 32-127 is 1.5" wide)?

My kids have these bunk beds and if you remove the drawer each drawers has one of these white slides/guides ?? that keeps the drawer balanced as well. I cant fina replacements for them.

Have a Hooker Hutch purchased in 2001 the hinges are 2 cup inserts 1-5/16 diameter with a total length of the 2 hinges is 2-3/4 inch

Do you have a video or instructions for replacing the Kerlin case runner 32-076? After installing a new Kerlin drawer socket and having difficulty putting drawer back in place, I am seeking a solution to my problem. Do you have other ideas other that replacing the case runner to get this drawer ope ... (cont.)