Viewing all customer Discussions for:

Drawer & Cabinet

I am hoping you can guide me to the correct bracket/socket set for my drawer. It says Unigrass 6600 on the slide. I saw a previous comment and ordered the bracket recommended, they do not fit. The depth of the part that snaps into the bracket is approximately 1-1/2 inches. Photos are below. Thank y ... (cont.)

Please, lookimg for spare parts, hinge MEPLA 654.350.53.00 made in germany, long time ago.

I am wondering if you can tell me the distance between the screw bases on the 32-349 soft close hinges. Thank you

We need to get a replacement for the guide in picture ending 8683 to go along the rail of the pic in 8687. Thank you for your help!

I need to replace a number of drawer slides for an old Thomasville dresser. The old ones use a ball bearing system - I uploaded some photos. Need either a direct replacement or something similar that will work for me.

Looking to replace the kitchen cabinet drawer glide as shown. It mounts on the back of the drawer inside the cabinet and holds the metal piece that the drawer slides in and out on- the track is approximately 11/16" wide. The plastic guide piece measures 2 5/16" wide , 1 9/16" high. The cabinet compa ... (cont.)

The white plastic part has no markings. Six screw holes. The almost square part is 4.3 cm x 4.6 cm. The rectangular slot is about 1.5 cm x 2.3 cm.

The piece to hold one side of my kitchen drawer slide broke. I need a replacement. Can you help? Thanks

I am looking for the plastic piece pictured. Just the right one. It holds the metal drawer guide for a kitchen cabinet drawer.

Do the pulls come with the screws tomount

Well, in trying to develop a work around for the broken rail hanger (picture sent to you an hour ago), I have discovered that the drawer stop on the side where the hanger is broken is also broken. I guess that should come as no surprise. Can you identify??

I have an old metal cabinet with roller bearings in the drawer slides. The plastic or nylon wheel broke. It appears to be a rivet axle style so that it fits flush against the cabinet wall.Can you supply the proper bearing and rivet attachment?Thank you!Dan

One of my kitchen drawer back left mounting bracket broke and I don't see the same one on your website. Is it possible to use a different bracket that might work just as well? Or do you know who might carry this one that broke (KV 1284-3)? Thank-you, Debbie

Hi, My wooden desk is by the Lexington brand. The desk's part number is 225-534. 850712 is the serial number I think. It was purchased in the mid to late 90's. I am missing the small knob for the top pull-out tray. It should be no more than 28" mm wide. The screw is about 3mm wide, about 5.5mm lon ... (cont.)

Hello, I'm hoping you can help me. I have a full kitchen in need of these (56 in total). The stamped part number appears to be 03030.67 and the spacing between the two screw mounts is 52mm. If you don't happen to have the same part, do you have anything with the same mount, 52mm or just over 2in ... (cont.)

I have attached a photo of the broken kitchen tracker, the intact drawer tracker, and the track it runs on. Also the drawer itself. Do you carry a replacement piece for the broken tracker?

Folks, Here's picture of the rear mount track support that I need. The track is 1 1/8" at the bump close to the end of the track. It is barely inside the holder. I've looked at 32-028, 32-003, and others but don't know which would work. The track was installed about 40 years ago. Your help will b ... (cont.)

Missing one of the pieces of wood for the bottom slide. Do you have something I could buy to fix these. The rest are worn, so I would probably replace them all.

do you have a Canadian Distributor regards David Hancock

Looking to replace a couple of bent drawer, glides on my kitchen cabinets.