Viewing all customer Discussions for:

Other

We are looking for rubber window gasket that would accept 7/8" glass and fit in a 1" glass pocket. Channel depth of gasket needs to be 5/8".

Good Morning- I am looking for black slide-in weathering backing is 1/8" and pile is 3/8". Could you please assist with this? Please advise. Thank you

Pictures of windows and jamb liner Wood windows with aluminum liner, which I believe is not double hung type.

Rollers shown are from neighbor's door, houses were built same time, same builder. My door is very hard to slide, especially as it gets colder. House was built in 2005. Rollers are stamped Delta 2188. Measurements are close to your 81-156, but enough different to make me check with you before orderi ... (cont.)

We own a 1992 modular home. The windows are probably original. BUT they are in good shape overall. They're double pane, "low maintenance", tilt in to clean. Metal window locks say "Carefree." Single hung. None leak.Some of the windows are hard to open. Once opened, some don't STAY opened. We have a ... (cont.)

Dimensions match your product 90-072, but looks more like 90-009 or 90-005. Hope these photos help you determine what product I need.

HelloI got this window useAnd am looking for a list 6 pieces of this This piece go on each side of the bar to guide window ? up and downWith out ,, window come of the guidance Luis If you have it send me invoice I will pay by any choice you give me Thanks

window weighs approx 16 lbs.The wings are just shy of 1in.the inside track width where spring resides is 9/16.from your site it look like s385.the metal length is 27 in.please help windows presently has no tracks as they were damaged as you can see from picture.thanksjay

Tilt latches, No part # anywhere on them or any sort of markings?

This is strip on inside bottom edge of a PELLA -040513 P0610108432 NFC PEL-N-181 shown in-situ and removed. Is there a replacement 31 inches long available

Hi, We are looking to purchase 1 x pair of rollers to replace the defective pair on a door measuring; Height = 2055mm Width = 1210mm Thickness = 35mm The number on the side of the rollers is; D-719 I have attached images to assist. Please can you either direct us to a UK based company ... (cont.)

I am looking for the bottom and top latch to a French door. The part in the picture is the bottom latch. This is very time sensitive, we are selling our home and the buyer is requiring us to fix the latch on the door can you all please HELP?

Hello, can you help me identify this part number?or the replacement for it please? I can't seem to find the exact shape in this size. Thank you, Bill

Aloha, We have some old windows that have a handle that slips on and then we have to awkwardly crank the window open. (handle like this: https://www.swisco.com/Wood-Casement-Window-Operator-Brass-finish/pd/Casement-Window-Replacement-Operators/39-268) we would like to retrofit it with some handles t ... (cont.)

Need to replace weather seal on heavy duty sliding window. T-shaped foam filled, fabric coated 1/4 in wide. Please recommend replacement. Thank you!

Need to replace tilt window latch on 2 American craftsman windows over 15 years old Model # 17297451 Bought at Home Depot

I have casement windows that were installed in 1980 and I'm 99% sure they are Pozzi, since Pozzi was a Bend company There is a 3/8"wide weatherstrip on the outer edges of all the operable window units that has deteriorated on all the windows that I'd like to replace

I have a customer that has an acorn dorsal sliding door that has an exterior trim piece that is split. I don't know if this is a replaceable part or if I need to try to reattach it to the frame.

We need this handle and escutcheon in white for the right and left side of the window

Balance for Ply Gem 1500 Vinyl Tilt Single Hung Window I am unable to find this hardware, are you able to assist