Viewing all customer Discussions for:

Weatherization

The bulb-type weatherseal on these windows is falling apart. I believe your 3/16" T-slot foam-filled bulb weatherseal, PN 58-182, will be the correct replacement. Please review the attached pics and drawing to confirm this for me. The extrusion is a little different than that shown in your on-lin ... (cont.)

I have an older anderson PS11 GL Oper sliding glass door and need to replace the rollers which I understand as being PN 81-018. I also need to replace the weather seals on the door. The ones currently appear to be stapled on except for the ones that go on the door frame where the door meets the fram ... (cont.)

Tube is close to 5/16 and T is close to 2/16

Hi, I am needing to replace the weather stripping and the brush sweeps on these doors. I could not find any markings or information as to what brand the doors are on them. Could you please tell me if the 58-105 or 58-085 would be the weather stripping I would need? The door sweeps I need are brus ... (cont.)

I have weather shield casements circa 84. I've been trying to find weather striping for these, do you think you have any.

I have several LP casement windows( 1991 vintage) that need new weatherstripping. The profile is very close to the Kerf Bubble Mount Seal 5/16" (58-504) . However, I am not sure about the wall thickness on the bubble itself. Mine appears to be thinner, possibly 1/64" thick. Could you please ... (cont.)

Hello we have swing doors for which we need to purchase weatherproof seal / sweep striping. Any suggestions for you? We have the following doors : zz_SOHMD_36489 - Elison 3/0 6/8 LWP3 Double Acting Door w/9" 3 x14" lite

I am enclosing a photo of a piece of the weatherstripping I need to replace around 2 casement windows. The entire piece is only 1/2" wide. there are no identifying markers on the entire strip. I hope you can help...this has been a real challenge. I would appreciate any suggestions you can offe ... (cont.)

Looking to replace old weatherstripping. The plastic base is approximately 3/16" wide. The top portion that is foam filled is approximately 3 - 4/16" wide. The overall height, from the plastic base to the top portion is approximately 1/4" tall.

Hi, the vinyl sweep on my fairly new pella storm door has ripped, so I was hoping to find a replacement. The top of the "T" measures about 5/16",as close as I could tell. Do you have anything that might work? Thanks!

Hi, I need a wool pile replacement for a Certainteed window. The information on the inside of the window says Half thermal. MFR 03/13/02. There is a number#411511-7 53 13 STOP 1 I don't know which size to order. Thanks, Steve

I am looking for window seals for Viking horizontal sliding double pain windows in plastic frames. The seals are gray, wool pile seals with a flat bottom which fit into a groove approximately 5.5 mm (7/32") wide and 2mm deep. I need a total length of 50 feet. Please, let me know if you have the s ... (cont.)

the part i'm looking for is a weather seal that slides in a channel on the lower edge of a vinyl replacement window - it appears to be a semi rigid rubber or plastic, sits at the outside edge of the sash, silhouette is round with a small lip at the bottom, like a Q.

I'm looking for weather striping to match existing, picture shows aluminum backing in channel in the door, picture shows "wool" has been removed and section. Sketch shows dimensions. Please advise price and availability. Thank you Eddie

Hi Swisco Customer Care, I am trying to install new weatherstrip on a commercial door. There is a Wool pile weather stripping on the back of the door against the frame. The bottom of the wool pile that goes into the frame channel is 1/4" The current height of the pile is 1/4", but likely ne ... (cont.)

The attached picture shows the operative door of a double door unit. Thank you. Eddie

What are the minimum/maximum design clearances for the 58-053 bubble seal? And is the 58-055 also made from Santoprene?

The part is on Anderson sliding screen door The bug flap ha 3/16 base and a half inch wool bug flap it slides in like the wool flap for windows Need a replacement

I need part number of this weather-strip. I thinks that is for a Keller window

I have Jalousie Windows with t slot bubble seals . They are 3/16 t slot width and 1/4 inch dia .. You have a t slot that is 3/16 x 3/8 # 58 135 . Do you have the 1/4 and if not do you think the 3/8 dia will work ok . attached is photo of the existing bubble seal . I used my vernier to measure the di ... (cont.)