Viewing all customer Discussions for:

Weatherization

this sweep attaches to the frame on the floor. the tube is 7cm. is this a piece that you carry or can order for me? thanks

Hello, Attached is the picture of the window bead for my alenco window glass.. it is "flat" piece of plastic approx. 3/4" wide with couple of small edges/groves at the bottom.. can you please let me know if you have replacement

Hi, I am looking for a weather striping height 3/8" and wide 1/2". I found a weather striping from a local store of height 7/16" and wide 7/16", but it was not fit my door. I need exactly right size of weather striping wide. If you have the one, plz let me buy it. In addition, I need a plastic b ... (cont.)

We are refurbishing an old commercial beer cooler that was likely built in the 1940s. The end view of the door gasket is shaped as a perfect number 9. The "O" of the nine is 5/16 of an inch in diameter and is sponge wrapped in a canvas-type cloth. The bottom tail of the "9" is straight (not curve ... (cont.)

I need some 58-161 that is 1/4" in pile height. What do you have?

The weatherstrip insert for the threshold of one of our interior doors has failed, and I have been unable to find a replacement. It was installed when we rebuilt our house in 2008. I​'ve attached both a jpg​ of the cross section of the weatherstrip, and a sketch showing its dimensions. If y ... (cont.)

Hi, I figured out that I need 9/32 x 5/16 wool pile for my four sliding glass doors. My question is what will retain, or keep the pile from sliding back out? The problem is the old seals are sliding back out, and then get smashed in the door jam when closing the door. Would you suggest some rubbe ... (cont.)

I'm looking for a door sweep for a Caradco French door. Hoping you can tell me where and which one to get now that they are out if business.

Hello, I want to buy a T-Slot Foam Filled Bulb Weatherseal. In your website I saw two listings #1: .187" (Product Code: 58-182) #2: ..270" (Product Code: 58-171) I am sending measurement pictures that which one is for my windows weatherseal strip? Please reply me ASAP. Thanks,

I have unknown make Vinyl windows about 13 years old with a proprietary molded weather strip rail on the lower sash (see Attached Pic. Can the manufacturer be identified by this weather strip? Will 58-164 work based on my dimension in the pic? Thanks you for any information you can provide ... (cont.)

Storm door model 248-TL Built 3/10/1998 Registration # 024881U.111980310 Door has two sweeps

This weatherstripping is from the bottom of the lower sash off a double hung window. The angle is about 1/4 inch on each leg, the included angle is a little less than 90 degrees and the bubble looks like it started out as a cylindrical tube about 1/4 inch diameter, although it's now pretty flat. ... (cont.)

WE HAVE A NEW COMMERCIAL STEEL ENTRY DOOR & FRAME THAT THE CONTRACTOR INSTALLED A TUBE SHAPED WEATHER SEAL ON THE FACE OF THE STEEL DOOR FRAME. IT HAS BEEN INSTALLED ONLY 2 WEEKS AND IS VERY UNSATISVACTORY. IT LEAKS BAD AND HAS ALREADY SHRUNK TO THE POINT THAT IT LETS SNOW INTO THE INSIDE OF THE DOO ... (cont.)

need some pile window weather strip for silverline 1200 series double hung window. the factory strips are small & light can be seen though between sash & frame.

Looking for 9 Lft of the rubber strip for our walk in cooler door sweep.

We have 2 types of door stripping between the doors. What items are these two that we should order? Please see pictures attached.

I am looking for the item shown in the attached picture. It is the grey felt lining that goes in the upper rails of my closet doors and the door rides in-between. The felt is missing in one of the rails. The closet opening is 6'1" wide.

Hi, I am looking to replace window weatherstripping throughout home. I have attached photos and dimensions. Please guide me to your closest product.

Please identify this

General contractor, commercial out swing wood double doors with recessed spline down the center that holds the astragal pictured above. 3/8 wide, metal 1/8" and do not know how high the wool pile was before but probably 5/8" where do I get this part