Viewing all customer Discussions for:

39-114L Crank Handle, 11/32"

I need to get a replacement dual arm operator. Seems to be K/K manufacturer. The distance between screws is 4 7/16 inches. The small arm is 3 15/16 inches. The large arm is about 10 inches. The small arm has a number 20810. Can you advise which replacement part to get. Thanks Albert ... (cont.)

The only part number that I can discern says 30806. There are some patent numbers (US 4505601) on it and says Made in USA.

Please let me know what part to order. I will then order five each. Thanks

Assisted living facility in Buffalo ny, in search of these window encasemebt arms. Possibly a Anderson window

Hi, I need help identifying this crank assembly for a client. Attached are pictures of the (2) part numbers that appear on it.

The 3 crank handles on our window are breaking off at the base (see photo right hand side)I need to identify and order replacement crank assemblies for Series #6100 Bow window purchased around April 2003, purchased from Home Depot, Allentown, PA. Also, I need instructions for replacing cranks. Thank ... (cont.)

I have some issues with some windows from Fibertec. For some the handle is spinning but the window does not open. Do I have to replace the whole mechanism or just the handle. I am enclosing pictures of the outside of the mechanism and inside. The distance between the screws is 5". The tie bar is tr ... (cont.)

Do you have an operator like 39-031 with a 3 13/16" link arm?

I believe this window operator is an Anderson. I believe these windows are original and our house was built in 1967,however I don't see any markings or numbers on anything. I did measure the arm and it's approximately 9in. I would greatly appreciate any help that I could get identifying the window o ... (cont.)

Please check attached photo and advise if you do have it

I'm looking for four of the attached pictures 2 are left hand and 2 are right hand . There is a Patton number on the back that reads 6.247.270 . I was told the item was discontinued.

The gear and shaft for the window is broke off from the rest of the assembly. We also need the latch for the window. It is a left side latch on the window and the crank is to the right side of the bottom of the window unit. The windows are from the mid 90"s. Part number on the latch assembly is 3 ... (cont.)

I have these circa 2008 (Milgard?) casement window handles. They stick out quite far and get in the way of the window blinds. Do you know if a folding handle is available? And if so, what might be a good color match? Thanks for your help! Sorry, I meant to put this under the folding spline handle, n ... (cont.)

See photos. Just need to confirm which part is the replacement for this?

I need to replace these cranks and their mechanisms . Not sure who makes them.

I am seeking two(2) replacement crank handles with covers to match existing on mid-1990's Viking Casement Windows. One handle with cover is needed to install at the bottom left position (looking to the outside); the other is located at the bottom right position (looking to the outside). Can you help ... (cont.)

IMG 2319 shows the left window with crank missing. It is the left window, if inside and looking out. The other photos (right side) show the type/size of window operator needed to replace the left window operator. So i'd like to replace the one operator in IMG 2319. Can you tell me what part that ... (cont.)

These are on 20+ Caradco Casement windows in a home we recently purchased (I've included a pic,too). Do you have operators, handles, and covers that will work? TY --Reed G.

Please see the photo uploaded. I am looking for the two parts that are circled in red. It appears that the screw piece is stripped, and the cover is cracked. The handle appears to be fine. Thank you!

Good morning, I am following up on my phone call this morning with a few photos. I am looking for 2 sets of replacement hinges/arms and locks. These are 25 years old and are Silverline windows from Hurd. Please let me know what else is needed. Regards, I measured one arm at 4 inches and ... (cont.)