Viewing all customer Discussions for:

58-085 7' Commercial Door Weatherstrip

I have been looking on your website at weather stripping. I think I have the correct part number for in between the doors. But I need to find out the correct one for the bottom of the doors. The doors are a double swinging door that measure 83.25

1/2" wide

Weather stripping The left photo is just like the door we have, and We need the top and bottom piece. (Vista Wall Adam Rite door weather stripping)

Do you have a faceplate (the piece that is around the lock on the door) that has weather stripping on both sides of it? I am purchasing weather stripping 58-085 for our door. One other question about item 58-085, does that come in 2 pieces or is it something you need to cut? Ours looks like it stops ... (cont.)

Looking for replacement weatherstripping for Kawneer door to non-profit organization. Need before cool breezes come! could not find and numbers or markings that is why I am needing help to find them and get them replaced.

Hi, what are the measurements of the 79-001 wpring clip? width mainly. thanks

I am in the process of purchasing barn door hardware and will be installing doors on this hardware. Best my contractor and I can guess - I will have 1/2" gap when the doors are closed (or pulled together.) The space has to be there to allow for clearance as the door slides. I am wondering about p ... (cont.)

I am going to install a swinging door between the kitchen and "office" and would like to have the door 'seal' somewhat when it closes. (center of jamb) Can I dado a slot and install a seal the door would stop at but go in our our? -or- What about a seal in the edge of the door for easier (more ... (cont.)

do you have this type of weather stripping< its rubber

To Whomever It Concerns, I wanted to order the 7

Hi, I am looking for a weather striping height 3/8" and wide 1/2". I found a weather striping from a local store of height 7/16" and wide 7/16", but it was not fit my door. I need exactly right size of weather striping wide. If you have the one, plz let me buy it. In addition, I need a plastic b ... (cont.)

General contractor, commercial out swing wood double doors with recessed spline down the center that holds the astragal pictured above. 3/8 wide, metal 1/8" and do not know how high the wool pile was before but probably 5/8" where do I get this part

This is for a glass double door (storefront). Wool pile is 3/8 wide and a depth of either 1/4" or 5/16" with a length of 7'. this weatherstripping back plate is metal that goes in the door track it has spring action clips and is held in place by screws going threw the wool weatherstripping ... (cont.)

hello, Can I purchase some of these springs, just the springs? what is the part number and cost for each? thank-you Greg

We have a Portal double push bar glass door that has wool pile on the left door. The door is over 10 yrs old and the pile has worn due to lots of use! The weatherstrip is held in by screws thru the middle of the strip. The wool pile also appears to have a plastic layer inside of it. Here are the ... (cont.)

I need to replace this weather stripping. It measures about 1/2" wide. 83" tall. Notice the gap between the doors... will this be a problem. Its so close as it is.

Hi I have a Kawneer double door and I need to order the replacement weather seal where the two doors meet. I have attached two pictures for reference. Can you provide a price for the weather seal? Please feel free to contact me with any questions. Regards, Ken S

Can we buy a set of 70-030 springs individually for our Church glass double door weatherstripping? Our Kawneer door has the springs as part of the 1/2 metal strip on the double brush stripping, not separate springs. I think we should try installing new springs and adjust our screws before we buy a c ... (cont.)

I had a gray wool pile on the bottom of my sliding door that came off. I'm not sure what size to order. The one that came off is 1 inch wide. And the door itself is 3 feet long. Which of your products do you suggest that I get to replace it? I need to do this as soon as possibl

How far apart are the holes for the mounting screws? On the stripping I have the first hole is 4 1/2" from the edge and they are 9" apart.