Viewing all customer Discussions for:

80-106 6' Sliding Glass Door Track

The track for our sliding patio door has come apart creating difficult in opening and closing.We Do not know the manufacture. I can see that the cap has detached along the majority of the track.We need to replace it. The track is 92 1/2" and if fits in a 1 9/16" Chanel.Can you help up find a replac ... (cont.)

I am in need of a track for sliding door model Pella 072820M022171369. I have put a piece of wood in to hold the door in place.

Hi I have a double glass sliding patio door track.I replaced the bad wheels on one door but the door is getting stuck only when you are going to open the door.The track is worn out in the one spot that the back wheel sits on when the door is closed.Should I install track caps or duetou sell the bott ... (cont.)

All the info I could get off the tag . Aama sponsored. Code-1 spec SGd-b1-hp-40.

I am trying to find replacement rollers for my sliding glass door. Here is some info from labels on the door. ?Label on side of panel (note SGD = Sliding Glass Door) ?Series M-800/M-825/M-850 ?SGD-R20 ?MST-12069 (00X) ?Manufacturer Stipulates Conformity to ?ANSI/AAMA 101-85 ?M

Hello this roller is from a glass door inside of a 1998 Horton double wide. It appears to be all brass.I don't see any numbers on the roller or the door itself.

The bottom rail for our sliding door is broken and need a replacement part. Anyone can direct me to where I can get this part? The rail is 178.5 inch (probably a 6 ft length) x 2inch. The label says AAMM Series 8500, SGD-R20

I'm looking for rollers to be mortise in the bottom of hardwood doors (1 5/8"Dx39"Wx80"H) that weigh 120lbs each. I also need a 6'6" track that will work with rollers. I was looking at the 81-184 tandem rollers and the 80-106 track, but I'm not sure that the rollers will handle the weight. Any sugge ... (cont.)

This track supports 3 aluminum frame polycarbonate sliders. Total Length is 91". Track width for each door is .750" Doors ride on Swisco 81-246 Roller Assemblies

Hello, I'm looking for 2 rollers (ball bearing type) and a retrofit track to replace the worn parts. Roller dimensions: -Wheel: concave 55/64" with 1 1/8" shoulders -Dimple width: three dimples measuring 61/64", 31/32" and 63/64" each -Housing width: 3/4" -Housing height: 1 11/64" -Housing length: 2 ... (cont.)

The track is so worn in places so bad that it is flat. It is a rounded track, but it is so worn the "cap" type of fix doesn't stay on. The rounded part is part of the bottom frame and it sit directly onto the concrete. To put any track in .we will probably have to cut the current track out becau ... (cont.)

Need new sliding base. Plastic and metal.

Could you please help me find this patio door track. The glass shows from Guardian. Thank you very much. I just purchase the rollers 81-044 from your website. Hopefully I can get the track too.

8 foot sliding patio doorwall (one panel fixed) seal (?) at movable panel is cracked and distorted. Looking for a replacement.We think the etching on the movable panel says PPG Herculite A CGSB12GP1Seal is made to fit in a slot in the bottom sill that is about 1 inch wide and 3/4 inch deep and the ... (cont.)

trying to replace the bottom track of a client sliding glass patio door. This is the track and not a cover. cannot find track with the ball type top and the bottoms rolled inward.

I have 3 panel glass spider on back porch. I replaced wheels couple years ago. Now I found flat spot in track rail causing door to stick. Need help seeing if I can replace

Hi, I need to replace bottom track of sliding glass door. If possible the whole bottom not just the part where the door glides. Thank you!

One pic is with the track fitted in the rails and the other pic without the track and only the rails

I need the bottom rail for my client I hope you can help me to found the correct rail

I've tried several primeline replacement and they are either too big, or the roller doesn't raise and lower correctly. These are the type that are sandwiched in between the bottom and side frame rails and attach via the long tab. I have since notched out the bottom of my door so I can remove and rei ... (cont.)