Viewing all customer Discussions for:

81-132 Sliding Glass Door Roller, 1-1/2" Dia

Dimensions 2" x 1.5" x 3/4" wide

Hello and Thank You for your help in identifying a replacement wheel assembly. My internet searching has been fruitless. I also checked your site. I'll need to purchase 8 wheel assemblies as I'm doing 4 doors. Any help would be MOST appreciated. Cal

Hello, I am looking for the part # for this wheel so I can order from your website to replace a set on my patio slider. Thanks for your assistance! Bob

Hi can you help me identify this roller? 1.5 inch steel roller. The aluminum frame is 1 15/16 wide by 1 9/16 high. It says DISCO 1214 on the side. There are no other markings I can see Thanks

Hi there. Looking to replace this wheel. 1-7/16" tall 2-1/8" wide Wheel is missing from picture

I recently ordered part# 81-081 which I thought matched the ones I am replacing but I was wrong. I had purchased rollers for an identical patio unit about 3 years ago but there is no history of the part # that I had order. I need help to identify the part that I need.

I have included the sizing as best as I could see. Photos from all views.

Rollers for an Aluminum Frame Patio Door and Screen Door. Installed in 1996ish.Need four rollers for each door. Two top and two bottom.Thanks,Ron

Hi I am trying to replace the wheels on my patio sliding door. Please help the dimensions are as follows: Sliding door wheel Height 1 1/2 inches Width 5/8ths of an inch Length 2 7/8 inches Long Thanks Tony

Appears to be a 81-009 Miller Sliding Glass Door roller?? Original as measured is 11/16" w X 1 1/2" h wheel diameter 1 1/2

Looking for proper replacement part for this patio door wheel assembly. Have not seen exact replacement. Hoping there is a later model that will fit. Had to partially remove side door bracket to slide original part out. Thanks

Sirs, I have two sliding patio doors that have become very difficult to open and close. The doors are about 8 feet tall and quite heavy. I was no longer able to adjust the wheel height and I assume the wheel assemblies are rusted or corroded making the adjustment difficult. I also no longer have the ... (cont.)

Need replacement rollers, nylon should be quieter. Would like rail plastic track covers that rollers would ride on.1.5 inches tall, 7/8" wide wheel diameter 1.5 inches

I received the rollers I ordered. Unfortunately they are slightly bigger than the current rollers. I'm attaching a picture, looks like an 1/8" too big. The wheel itself is 1 1/2" I saw the model 81-261 was wondering if that might work?

patio door wheels need replacement part number

These are a picture of my old roller in the sliding glass door. On the side is stamped 159 and it is a 1.5" wheel. I am looking to replace all of them. I have looked at all the big box stores that do not have this size. The closest is the Barton Kramer 461. It is too big by 2 MM. Please help! ... (cont.)

Please assist in identifying this

Photos showing single roller was removed from one of the sliding glass door pane approx. 10 years ago. Photos showing tandem rollers was the rollers used to replace the single roller.The part shows DISCO 2136-1. There are approx. 24 door panes in need of replacement. They range from 5'x 8' to 3'x 6' ... (cont.)

I'm looking for four (4) sliding glass door roller assemblies as shown in the attached photos. Its dimensions are 2-15/16" long x 1-7/16" high x 3/4" wide. I couldn't get a tape measure directly on the roller, but the o.d. of the roller appears to be 1-1/2". There weren't any markings on the door, b ... (cont.)

my door has no name plate or model number I need the two door rollers and the door latch with lock