Viewing all customer Discussions for:

91-140 Larson Slide Bolt Set

both original latches were made of pot metal and are broken.

I have window latches stamped HK 701L and HK 701R picture provided. Closely matches 91-0022/23 latches. However the outside ends are not flush, but reduced as can be seen in second photo.

I'm looking for the storm window latches in the photos

top left( 1st pic) and bottom left (3rd pic) latches are broken. Top right and bottom right are fine. Please suggest replacement parts.

I can't figure out which ones I need for the drop down storm door windows. Please help!

Hi, I ordered and received a 91-140 slide bolt kit. It is exactly the correct one except the tip that locks the window in place, is 3/16" wide. My that broke off, are only 1/8 wide. the new ones are to "fat" to fit properly in the slot that keeps the window from moving up and down.. Any help would b ... (cont.)

Need to replace left window latch (end tab that holds window in door broke off). Is 91-022 comparable to 91-140 since I only need left one?

Dear Customer Service, Upon receiving my order it was discovered that the 91-140 : Larson Slide Bolt Set was not an exact matching part, although very close. After speaking to one of the representatives, it was suggested that I send photos of the part I am trying to replace. Hopefully wit ... (cont.)

says triplex on it (Left side), the right side latch says Royal

I had placed an order with you order number 74385 for and bought what I thought were the replacements for my storm door window slider clips as you can see from the picture the one on the left is considerably smaller than her it is broken the end clip is broke but can you maybe identify a different c ... (cont.)

Good Morning, We have a storm door latch that we need to match. Can you please advise which latch you would suggest. I am thinking the 91-140 is correct. Thank you for your help Holly K

This is the good latch. The right hand one is what I am looking for. If you can offer any insight to getting one I will most appreciate it. Thanks for your time. Mike

No name or markings on the door and had already been removed before the picture was taken. The part tha is broke is what holds the storm windos in position on the storm door. It is a glass storm window.

I need 2 latches (1 right side and 1 left side)for a Larson Storm Door Window. Pictures are 2 good ones and 2 broken ones. Do you have a pair for my window?

I am trying to find a set of window latches (right and left) for a Larson model 550-23 storm door. Do you carry these latches and if so what is the model number? Thank you.

I have a few storm windows with broken slide bolts. They don't resemble any in your catalog. I figured I would sketch the channel, and maybe you could help out (see attached picture). Your 91-140 looks promising but I thought I would verify before ordering a bunch.

I'm trying to replace these window latches on a storm door. there are for total top window and the bottom window. I watched your videos, I'm wonder if my braces pound apart or do I have to drill the indentions out to replace the latches. The latches are all broken and some pieces missing on one sid ... (cont.)

Hi, I found the slide bolts I need, it's Larson Slide Bolt Kit 91-140. It's the corner clips for a storm door window. I need help with. They are Left and Right handed clips because when laid flat there is a difference in height, the short leg being smaller as shown in pictures 2 and 3. Also in pictu ... (cont.)

*2004 PPG Herculite (storm door) *its the piece right in the center of the picture, between the screen and the glass *the part the holds the glass is broken so it stays slid down *can you please email me any information you might find? Thank You

As you can see on the attached picture, the top right fixed latch is broken and both the bottom spring loaded latches are broken. the window frame measures 5/16 wide x 21 3/4 x 26. Do you have these replacement latches and some instructions on how to remove/install?