Viewing all customer Discussions for:

95-206 Square Cut Corner, Pair

we have several hundred window screens that use these corners.the tops have a hook that holds the screen in the frame so i would need a left and right,the bottom ones do not.there is a flat edge around the outside of the center piece that has broken off of the one in the photo.THE CENTER PIECE IS 7/ ... (cont.)

To Whom it may concern, I would like to know if Swisco carries the parts shown in the photos. One of the keepers interlock into the edge of the window frame and the other one is with no lip being squared off. The rough opening of the screen frame is also shown. Thank you in advance for your tim ... (cont.)

Screen corner from superseal windows from approx 19 yrs ago. Looks like one leg says Bayform and other has DP307078 and RD63647

Greetings - I believe this is a milgard window but I've been having trouble finding the corner of the screen with the little retainer clip as pictured. The screen is located on the inside of the window so needs the integrated clip. It's a Bayform corner.Thanks.

Good morning I received 4 pieces of replacement corner parts (96-206) from your company and they are a little big to go to screen frame.I am sending you two photos to determine what part you can match. Size of groove is 3/8 and length to each corner is 1 3/4 inch. Please let me know what do you reco ... (cont.)

I bought a 95-034 thinking it would fit my 3/8" x 3/4" tall screen frame. The part legs were too wide at 17/32" versus the 7/16" I need (see picture). The other leg dimension is too wide at 3/8" versus the 5/16" I need (see picture). The square corner was 3/4" versus what I need of 11/16" and 9 ... (cont.)

I need to replace numerous corner keys for screens used in window manufactured by Keystone Bldg Products that might be 15 to 20 years old. The bottom keys have what I would describe as handle to pull the screen in and the top (pictured) have a notch to hold it in. I could do without either of thos ... (cont.)

The screens have two different type corners. Upper corners have tab that goes inside the window frame. The first pic is a lower screen corner. The second pic is a lower corner i had to destroy to remove. The flange of the corner is broken offThe third pic is info that are on my windows.The fourth ... (cont.)

Replacement part for this rivco screen corner

I bought your part numbers 95-206 and 95-205. They fit nicely into my screens but when you put the screen completely together it is smaller than the original size. As you can see from the attached picture, the block where the screen rails come together is a little smaller than your part. Do you ha ... (cont.)

Dear expert, I am trying to find the screen frame corner to replace the broken one shown in IMG_3410.jpg and IMG_3409.jpg The side of the frame is shown in IMG_3408.jpg and its dimension is shown in IMG_3411.jpg The frame corner size is 13/16 square. I know the standard size should be 3/4, but some ... (cont.)

I am looking for this screen corner to build new frames for a customer.

I am looking for the following two items. The first is corners for 5/16 knife frame, and the second one is locks for the same. I hope you can help me.

Good day. I've been trying (unsuccessfully) to find exact replacement corner brackets and frame material for Milgard windows. I've even tried contacting Milgard again, without success. I'm a handyman planning to start a part time business in a housing development where ALL of the windows have these ... (cont.)

We need the 95-206. The screens that we do only use that type on the top and we use the ones in the photo on the bottom. Is there a special corner that is used? I need the corners like the picture that I sent you. The one that was removed from the customers frame. 95-205 looks as though it has ... (cont.)

WE NEED THE BOTTOM FLANGE CORNER THAT WILL GO WITH 95-206 in bronze

can you direct me where to purchase these

Windows made by interstate window and door Pottstown PA. Could not help said to contact you. Hope you can help.

Do you have any corners like these? I do not know what make of window it is but they corners have all broken. they have a flange on it. thank you

I believe these are Milgard windows and i'm looking for the metal screen clip for a casement screen. In reviewing the parts on your site they do not appear to match. Do you have any recommendation as to what this part is or where to get it? Thank you!