Viewing all customer Discussions for:

23-041 Mirror Wardrobe Door Roller Assembly

I have three doors so I need triple track for the bottom and the headers for the top

I moved into a home that we recently remodeled. The closet doors are Stanley. I have included a picture of the label. We re-carpeted the floors and I didn’t measure where the bottom track was installed in relation to the top track. Can you provide me with installation instructions please? Thank you ... (cont.)

I need 6 of thesel plastic u-shaped 1 1/2" high, goes on the bottom of mirror, wheel clip.

My bottom rollers have an extra plastic piece that clears the track channel. Do you sell extras? Some are missing. Also, woukd you have replacement bottom tracks? Tracks are 72 inches long. Stanley monarch.

The only number I could find on it was 4011. I would like to know how to remove and replace the rollers. I didn't see any attaching screws. I have 6 of these in various condition. Some have wobbling wheels. Other just don't roll well. Also, what can I look for on the track for damage? Do you have ... (cont.)

Does the number in this picture identify what kind of roller/wheel I need to replace on my sliding mirrored closet doors? Thank you, Debra

one of the doors keeps coming off the bottom track. do you sell anything that looks like this? thank you

I am looking for the bottom track for a sliding bypass mirrored closet door that is at least 15 years old and made by Stanley. Attached are photos of the top and bottom rollers, but I am not sure which is which at this point. I think what I need is 23-242. Should I also buy replacement bottom roller ... (cont.)

I ordered a few parts, the cam and I didn't want to install them immediately. When I finally did, I found out that they were wrong. I can send you the a picture of the correct and incorrect part for a little help figuring out just what I need. The silver ones are the ones that I previously ordered ... (cont.)

I need 4 new rolers for the doors Can you please help me with this issue. I can't find them anywhere here in the netherlands. I'm sorry for my poor english With regards Eric

Photo is installed

It looks like you have exactly what I need to replace a clients sliding door assembly & tracks.. I've attached a picture. It appears that the current door assembly has a "4011" stamped on it, but cannot tell. The wheels keep coming off the track, so I don't know if we need to replace the wheel as ... (cont.)

Hello, my very heavy sliding mirror doors have rollers marked ACME 4011 roller in a 4012 frame. They appear very similar to your 23-041, except that the nylon roller thickness is 3/8" not just 1/4". So the 23-041 ends up slipping through the track slot. Do you have a roller which is thicker, ... (cont.)

Hello costumer support. Need some help Looking for few replacement pieces for my old slide doors .1"stanley 4012 " ( 4011 inside) " I have seen on your web that the product code "23-041" is the exact same for it , am I right ?? 2. Does the new design model on your web product code " 2 ... (cont.)

I have a mirrored sliding closet door with a broken roller assy. Pictures are attached. Part # looks like 17-4254-000 made by Stanley Does Part# 23-041 replace this part. If so is it in stock and is their a Cdn distributor. Thx Bruce

I need to replace the rollers that run on a track

Can you help me identify this part? It is the bottom roller on a glass sliding door. Thanks! Mike

I am looking for the bottom roller for a glass sliding door. Picture is attached.

I cannot figure out how to remove the broker mirrored closet door roller to install the new one 23-041 I purchased from you. Can you please email instructions to me on how to remove the old one?

Both rollers on one door have flat spots and the door is difficult to move on the track. The instructions list "Accent 210/215/220/410/415 Prism 320" #4016 is listed as the bottom roller assembly. Which of your parts do I need as replacements?