Viewing all customer Discussions for:

10-320 Shower Door Round Top Sweep

The glass door is 1/4" thick and 66 3/4' tall: This needs a flap to seal the water from coming out of the shower. The door frame has a 1/4" T shaped slot that the previous sealer was contained. The pictures of the door sweep shows 3 screws that locks in the sweep bar. I sent you a copy of the h ... (cont.)

Can you tell me the diameter of the bulb top of the sweep.

Am in a small town in south central Florida ... no one seems to be able to help me with this weatherstripping I struggled to get out of two windows that were corroding and leaking water inside. There is a small channel that the weatherstripping goes into shown in first photo - It looks to be about ... (cont.)

I am looking for replacement sweeps for my shower door. I know I may need to "customize" any part that I receive to make it fit. The bottom seal was originally held to the frame behind the drip rail with adhesive tape and screws. The side seal may be more of a problem to find since it is 67" long. A ... (cont.)

Basically, I am looking to replace the rubber (round top) shower door bottom sweep piece that slides into the shower rail attached to my swinging shower door. Does that make sense? The problem is my shower door is extra-wide as I believe it was built to be wheelchair-accessible. Most sweep replaceme ... (cont.)

I need to replace sweep on my shower, I need help identifying the manufacturer. I'm not sure if the sweep slides out or if I have to replace the drip rail also. It does not screw on.

The sweep also has no holes. I took it apart to paint the frame and can't figure out how to put it back together. There are three nails which go into the piece which attaches to the door but no holes in the sweep. Do you know how it might go back together? Old shower ~25 years in good shape. The swe ... (cont.)

I am looking for a replacement for this broken glass shower door sweep. It is approximately 23.5" long, with two screw holes, approximately 17.5" apart. Do you have anything that matches this configuration?

Does 10-320 come in 1/2 inch stead of 1 inch ?

I need a sweep with 1/8th inch round bead and 1 and 1/4 sweep. Do you carry anything like this????

Where can I get a replacement of this type of aluminium sweeep? 21.5" long, 1st hole- 4" from edge, then another 19" and has another hole (or 2.5"form another edge). The bottom L is about 5/8", about 6/8" slight bend.

Do you have a 10-327 type sweep that's longer than 3/4"? I need the sweep to be 1. ".

I'm in need of a replacement shower door sweep. I've included a picture of the aluminum hinge part. The sweep goes up to that and then the seal slides into them both. I'm having troubles finding one.

I recently ordered and received a Round Top Sweep (#10-320) for my hinged shower door. The round top is too large to fit the door track. Does SWISCO sell a similar sweep with a smaller diameter round top? If not, can you offer any suggestions? Thanks... David Rockwall, TX

hi I'm looking for a shower door sweep similar to this one: Shower Door Round Top Sweep Product Code: 10-320 But the one I need is 1/2 round top See pic Thank you

Please see attachments and tell me if you have replacement rubber for my sweep. The door has no markings on it that I can see. it is probably 30 years old. I tried some of your Product Code: 58-162 and of course it is too wide to fit the sweep slot and trimming it down will not allow it to stay i ... (cont.)

I may be able to use this seal. You show tearfoo strips to adjust height. I need approximately 5/8" rang. Can I get it. thanks Paul

Hi - I have previously purchased several of your shower door sweeps - part 10-310 - but I don't see it listed as available any longer. Am i missing something? Alternatively, is there a comparable part that you recommend? Thanks