Viewing all customer Discussions for:

32-119 Grass Adapter Bracket Pair

Hello, I need to replace two of these parts that are on the backside of a Cardell cabinet drawer. The metal tracks slide over this part at the back of the cabinet. Can you order these?

Is 32-119 the correct replacement part posted.

Hello,I need to replace at least the right rear drawer support bracket. The rail aperture measurers 3/8" wide x 1" high. See attached photo. Do you have any suggestions?Thank you!Bob

Hi there,From other posts, I'm thinking these plastic clips with pegs are nearly impossible to find. The pegs broke for one drawer, so now the rail won't attach to the back of the cabinet. I'm guessing I'll need to reinforce the back with wood and find a new rail system with screw-in back mounts. An ... (cont.)

Kitchen drawer

Looking for replacement bracket for this piece. G600 is visible on the piece.

Hello. I'm in need of a Ferrari G026 drawer bracket left side as seen in the enclosed photos. The dimensions are 4 1/2" long, 1 7/8" wide, with a stop at 3 5/8" from the back of the cabinet. The guide is 3/8". Thank you for your assistance. Ray

Good day. Please help me find a replacement part that will not require me to drill! Thanks so much.

I need to replace the actual drawer but the drawer slide and bracket need replacing as well. Can you help find the parts or suggest something similar/better? The bracket is cream/off-white and holds the drawer slide at a 90 degree angle. The bracket has plastic tabs on the back that holds onto the ... (cont.)

This plastic drawer rail rear socket has broken and needs to be replaced but I'm not sure which one it is in your product listing. So if someone can provide me a part number and price, it is greatly appreciated.

I need a replacement slider for a Merillat cabinet drawer as shown in pics. The slider wheel is worn out. Thanks

I am trying to find where I can purchase replacement drawer slides that match this size profile but are longer. The only identifying marking is "UNIGRASS 6600". What I have installed now is 50cm long which leaves about a quarter of my drawer under the cabinet and not conveniently usable. The piece a ... (cont.)

I need the plactic piece u see in photos that the runner fits into. This is on a merrillat kitchen cabinet drawers. It has side mount runner that fits into plastic piece on back of cabinet. The drawer then fits into the cabinet side rail. Notice how the rails are angled down at end as it goes in pla ... (cont.)

The cabinets were installed in 1992 by the previous owner so I do not know the manufacture. The inside dimensions of the socket are 3/8 by 15/16 and 1 1/4 deep. The exact replacement would of course be best, but if there is one that requires screw mounting with everything else correct then that wo ... (cont.)

I am in need of a replacement drawer bracket and I am seeking assistance. Could you kindly provide me with a recommendation for a suitable option? The current bracket is made of plastic and I would like to ensure that the replacement fits properly. I have been suggested the Rear Mounting Bracket Pai ... (cont.)

I am looking for a replacement for a UNIGRASS 6600 drawer slides. The cabinet mounted rail is approx 23&1/4". The drawer slide is approx 22&7/16". The measured width of the slide is approx 1". Distance between the two cabinet mounting locations is 20&7/8". Markings on the Slides UNIGRASS 6600 ... (cont.)

Hi, I was looking on your site to see if you have any replacement parts for a 1990 Merlilat kitchen drawer. I have uploaded few pictures one is the sticker another is a functioning part and the other shows the broken one. if you could tell me which part I would need, I would like to purchase a cou ... (cont.)

My home is 34 years old and these are original to the house. Brackets are breaking. Need to replace several, Thanks

I need 8 sets ( left and right ) kitchen drawer aft supports

Hi I am looking to replace a few sets of drawer slide backs as pictured. They are marked ADAR Left and ADAR Right. The dimensions are in the pictures. Hoping you can help. Thanks Steve