Viewing all customer Discussions for:

32-336 Grass Under-mount Slide Locking Device Kit

I have American Woodmark cabinets. I am looking for a set of clips, like the photo attached to replace on a drawer. Please help!

The Picture is for a Slide Locking Device for a drawer slide. it is approx 2"x3" it is marked L (Left) on the bottom. The items and the drawer slides do not have any manufacturer markings or numbers on it aside from a R on both slides of the slides and what I believe is a date code of 11-08 ... (cont.)

This was a standard part on Quality Cabinets about 10 years ago. They referred us to this site

Hello, I would like to know which ones to buy or just buy Grass Flange-mount Locking Device Kit Product Code: 32-341 and 32-336 to set which one fits. The tooth part that supplies the press is broken. Thanks, Harold

I hope you can see the picture of a cabinet drawer lock that is included. This is a drawer lock part for the right side and I need a left Side drawer lock replacement part. Patent number is 7549712. The cabinet is Quality Cabinets and I contacted them and all they have are ones for the right side ... (cont.)

Enclosed photos of an intact piece and a broken piece respectively.

I'm in need of a Quality Cabinets kitchen drawer under mount left side plastic locking mechanism. These cabinets were installed in July/August 2007

Sending photo Let me know if you can help locate Thanks

Hello, thank you for helping me. I have looked online and talked to several cabinet people locally, but have had no luck with this. These little parts that hold and release the rails on the bottoms of several of my drawers have broken. I would like to replace them with metal (or mostly metal) par ... (cont.)

this attaches to the drawer, and has a slot for the slide. 2 are needed for each drawer.

I need to find replacement parts for the white brackets that mount to the bottom front side of the drawer. It attaches to the sliding rod that the drawer slides on. Thanks for your help

I have a Munire dresser for my kids and the white clips underneath the drawers have broken on preventing the drawer from closing properly. I need three sets of these clips. The metal rails are attached to each side of the drawer and clip into this broken fitting. Do you have the part, or a recomm ... (cont.)

We have a kitchen drawer that is 9 years old. The plastic part at the front under the drawer has a broken part so it needs to be replaced. Attached are the photos of front and back. Thanks.

Hello, I have been searching the internet and can not find a replacement for my drawer part. I see you have lots of parts and am hoping you have this one, too. Please et me know, I need the left and right, I think. Thank you so much, Evelyn

We tracked our kitchen drawer hardware to HGH Hardware in Birmingham, AL who purchased the components from GRASS. They contacted GRASS who referenced us to you. We have drawers with these rails: 76050-03 (60496-03) METRO ELITE PLUS SLIDE FULL EXT AIRMATIC 21" (21-5/8"CM21"DM). They are 7 years ol ... (cont.)

It is a drawer part mounted to the front of the drawer and serves as catch to keep drawer in cabinet. The mounted edge is 1 and 3/4 inch. The other square edge is 2 inches and the pointed edge is 3.5 inches to the point.

I need replacement drawer glide locks. These are approximately 1.75 X 3.75 inches. Installed with the cabinets around 2006.

Hi I have these slide mechanisms on my cabinet drawers, & I'm stumped on how to adjust them so my drawer fronts will be level. I find I have a lot of play in the actual rail that the drawer sits on on only one side. Is it possible it needs to be replaced? Do you have any idea how to adjust these par ... (cont.)

Hope this pix helps

We already ordered Grass Under-mount Slide Locking Device Kit from you, but now we have discovered that we need the mounting bracket part that goes connects to the drawer itself. Then we will attach the Slide Locking Device into that bracket.