Viewing all customer Discussions for:

Closet

Stanley 64564-001. I need to find an original track for this set of doors or know if a regular bifold track would work? the track was not the original and was broken. it was placed on two 30 inch tracks that did not meet in the middle. The left side opened but the broken track on right did not and d ... (cont.)

need two of these

Need replacement parts for a monarch mirror door part number on tag is part # 1201 came off a door dated Aug 15,1983. It also had #16CFR part 1201. Do u have a replacement for this

Need 1-1/8" tandem roller setups for dual pane Windowmaster sliding glass patio doors circa 1990. Panels are 48"Wx96"H. Original wheels were vinyl tandem. Need the same, but in Stainless Steel rollers.

I'm trying to find replacement closet door bottom guide marked DSH 20121

Plastic wheel

This seems to match what I am looking for but I wanted to know if the pin pushes down below the plastic casing (open on the bottom) or if it stops at the plastic bottom of the casing (closed bottom).

Hi I'm looking for replacement sliding door hangers for my house. The look exactly like this part - KENNA TRACK REAR CLOSET DOOR HANGER, 3/8" OFFSET 23-048 however my slider wheel is 3/4" rather than 7/8". Is there another part I can order that has the smaller wheel? Thanks, Adam ... (cont.)

Hi. Inquiring about the 10-057 ball catch. My old one is 5/8 diameter across the bottom and 1 5/16 inches from bottom to lip ( ball not included) also, the cylinder of mine is completely smooth all around. I noticed most online have some kind of hooking latches on 2 sides. But your looks like it wo ... (cont.)

bottom steel track for mirror slidind door #663-969

Hello on one side of my mirror the bottom wheels have come a part, which caused the trim come a part as well. I want to replace the guides or the top and bottom tracks along with the guides. Thank you for your help in this matter.

Hello, I need to order a 72" SLIDING MIRROR DOOR BOTTOM TRACK part #23-242 in satin nickel but also need another order for the same type of track but need to have it in 107". I was wondering if i could get a custom length of this track. It is replacing an existing one piece track. I appreciate and h ... (cont.)

Hello Swisco, I am looking for a top mounting bracket that is currently being used with a Grant (pc 23-189) four wheel trolley. I can find no markings on the bracket so I am not even sure it is manufactured by Grant? It is 3.5" wide x .75" deep. Can you help identify? Thanks, Niko ... (cont.)

The wheel on the lower end of the bracket (that fits into the track)is broken. The name on the back of the bracket is COX ,under this is the number21-77 and under this the numbers 21-767. The system ;track and sliding doors are part of a fitted bedroom wardrobe, installed about 26 years ago.I would ... (cont.)

Trying to locate proper sized roller for top of bi-fold closet door. Roller diameter is approx. 11/16" or 18mm. The pin holder that inserts into the door (or anchor) measures approx 7/8" to 1/2" and is about 1+1/8" deep. Shafts are about 1/4" (narrow part) and 5/16" (wider top part) ... (cont.)

Please review the attached photos. The measurements of my door roller match up to your 23-028. However, the only concern I am having is that there seems to be a hook in your door roller that I don't have and wanted to know if that is going to cause an issue for me. Could you please let me know i ... (cont.)

Local hardware store found this info Small model #6717. 5200274 Big ?? AFC is the only marking 1960 vintage Charles

Many of your posts recommend P/N 23-028 as a replacement roller. I noticed my roller does not have the two tabs on the top of the roller that make a 90 degree turn toward the front. Will they be in the way during installation. Thanks

Part has number 20121 on it. I need a replacement and to know how I remove old part from the door. I read that it pops off but I don't see a way to do that and I don't see screws.

Looking for some hardware for sliding by pass doors for a closet in my 1912 house. Length of hardware is 3 5/8 bottom of bracket to top of wheel About 3/4 height on wheels, could have been 1 inch but they are very worn metal wheels. the wheel edge thickness is very narrow. Its about 1/2 inch ... (cont.)