Viewing all customer Discussions for:

Closet

I am looking for a replacement for this stanley roller I hope you can help

I am in search of replacement sliding mirrored door glides and installation/replacement instructions. Markings on the old glides are DSH-20121. Glide appears to be 1 7/8 in wide. Thanks in advance.

I have two closets 72" wide with top and bottom track. Mirrored doors were discarded along with their hardware. I plan to use wooden doors but don't know what hardware I need. Is this your product?

In 1991 two closet Monarch bifold doors were installed, one closet has three bifolds, approx. 90 in. Wide and about 75 in tall; second door has 4 bifolds, approx. 120 in. Wide by 75 in tall. Tracks are installed. The top and bottom slides are "shot". No one locally seems to have replacements. One s ... (cont.)

Hi I need replacements for a Hamilton Ind, cabinet w/ sliding doors, what is the dimension for distance of the wheel from the bracket?

Hello, I took a chance and ordered part # 23-240, then yesterday I found the old rail sitting out in the junk pile. My new part arrived today. Before I open it, can you please tell me if you think it will work to replace the old rail, or should I order something different? I appreciate your help! ... (cont.)

Good morning, Our home is older and the hardware for the doors have been very hard to find. Can you please assist in letting me know what replacement hardware needs to be? I have attached a picture of what the hardware looks like. The information that is on the hardware is as follows: 3/4 F ... (cont.)

I am looking for replacement part for this closet roller. Can you help? Thanks

Does the top bifold pin 21-018 come with a cone spring?

I am having a hard time locating this part. My closet door is hanging off the track ok one side and this is the missing piece. Is there a similar part that would replace this, if not the exact same part you may have in stock? The part number is DSH-20121.

Morning, I recently ordered your # 84-137 roller assemblies. turns out these are to large. I need a 3/8 thickness instead of a 7/16. Do I need the 84-011? Please advise when you can.There are no numbers on the old rollers Thank You Darryl

I believe this is the correct part. The numbers I have on my convex wardrobe roller (for which the roller broke in the middle so only 1/2 a wheel is on the roller). are 21-717, 21-767 and 21-718. Sure hope you can help. No store around the Palm Springs area nor in Idyllwild has the part. Th ... (cont.)

I am purchasing the 23-240 to replace our rusted Stanley track. Am I correct to assume if I install the 23-240 so the roller tracks are in the same position on the floor as the channels of the rusted out track, the existing doors should work in the new track? The distance between the 2 roller chan ... (cont.)

I am looking for a part similar to this bottom roller on a sliding mirrored closet door. I might have to buy a pair. stamped with 21-717, 21-767, 27-718

I ordered rollers (4) 23-064 : Mirror Wardrobe Door Roller, Concave They do not fit. I have attached a picture. I believe the distance between the screws is 2 3/16 " I also ordered the top guides to replace the K guides. These are also not right. These doors have a wooden frame, and those guid ... (cont.)

I have a 1940s era cedar closet with doors that roll on an upper track. One of the wheels on the hanger fell off, and I cannot find a replacement anywhere. I am looking for a wheel that is 1/2 inch diameter and the bracket is flush, not offset. Do you have anything that could be a close rep ... (cont.)

I am a little confused, you show a pin cap 21-108 along with the 21-402 track in many of your suggestions, but you mentioned that this cap will not work with this track. Which track will the 21-108 cap work with? I am replacing all of the pins and tracks on a S376305 door. closet opening is 5 foo ... (cont.)

My bifold doors uses a stanley 2819 part to secure the top of the stationery rotating door ... do you have a replacement

I need a lower closet door track. the track is approximately 3 1/2 inches wide. Two doors slide on it. Im not sure if I need the 23-272 or another model. I can't get the pic. to load onto my portable computer but have pics on phone. Thanks for help. Tony

I am looking at bifold door hardware and I am wondering if some of the hardware is made out of aluminum. Like for example 23-114, 23-112, 23-139, 23-135, 23-506. And I am wondering if this piece, 23-312 is made out of some sort of steel or not.