Viewing all customer Discussions for:

Closet

I have a pocket door that uses the 23-255 hardware. The door is out of alignment, with one end much lower than the other. How do I adjust it? I tried unlocking it and turning the little white plastic wheel, but nothing happens. There is no way to get a wrench up in there to physically adjust the ... (cont.)

I have a Stanley Mirrored sliding door Part number 64564-001. I need a bottom track for it. The measurements for the track based on how ya'll measure bottom tracks is 1 5/8 --- 3 5/8---47 Please help identify correct bottom track for purchase. Refer to photo included for reference. ... (cont.)

I have a pocket door with a wood track. The track has a 3/8th cut out. The wood track width is 1 1/2 in. With the 3/8th cut out and the top track is 1/2 in. Thick. The roller would need to fit on top of the wood track with a bolt drop down through the cut out and connect to the top of door brack. My ... (cont.)

Can you tell me the size rod this bracket will take. I need one that will take a 1/4" pivot rod. Thanks!

Hi, Any help on this is appreciated. I have attached pictures of the top and bottom pivots as well as the top/bottom guides along with their measurements. I would like to know if you have these parts available as well as the springs. These pieces came off metal bifold closet doors. Not sure of t ... (cont.)

Does anyone have this?

the wheel is attached to a rectangular 2 walled metal with a part that slides up and down a track.

Installed a 8' door set about 15 years ago. Over the past few years the lower track has begun to curl upward away from the floor. This has occurred slowly and began to affect the ability of the doors (one in particular) to slide easily. At this point, one door cannot be opened without brute force ... (cont.)

How do u adjust the sliding mirrored doors?? When they close, there is a gap at the top??

Attached is a picture of the guide I need. I ordered a replacement door, but the new guides CW sent were inadequate.

An image is posted above. We need 9 sets of these rear by-pass hangers for our Bifold doors. We have 9 doors all together. Each door base 2 of these hangers with a wheel on it. We just can't figure out what exact part we need. Hope the photo helps. Jeanne

Hi...I am looking for these nylon parts which have broken off. The doors are from 1987. I think they were originally to have mirrors, but we asked for them to be plain from same company. If you can help, I would appreciate it. Thanks Frances

I cannot find a manufacturer or other distinguishing features, but pic 006 is of a similar door showing a top pivot. The actual pivot rod that I need has a different pivot bracket, as shown in photo 007, where the 3/8 inch that goes into the bracket must be 1/4 inch. I also need one bottom bracket ... (cont.)

I ordered 8 of part 23-047. The roller is flat not round like the old one. Can help with the proper match or remedy ? Fits to tight in track. Brad

Need corner connector to raise height of bifold door. Need the bolt that goes through the connector that pushes down bottom roller pivot. Does that bolt come with corner connector?

I need to replace a roller that only has "U.S.Pat.4850145" and 23-028 was recommended in your blogs but my roller mount is on the opposite side. Is there another option?

i want to order 6 48" bifold door tracks 7/16 pin (code 23-454) will your wood door plastic guide cap (code 23-146) slide freely in that track

Hello, I hope you can help find replacement parts for broken wheels and wheel assemblies for Fleetwood mirrored sliding closet doors. They were installed by California Closets in 1989 and that company does not use Fleetwood closet doors any longer. I've uploaded photos with measurements. Than ... (cont.)

I am not familiar with the given numbers but would be happy to research it for you. Please reply with detailed photos with measurements.