Viewing all customer Discussions for:

Drawer & Cabinet

Hi We are still a year out on replacing the kitchen and the current brackets keep braking Do you carry these oor something that would work. The brackets that hold the rail are 1.25 inch

The rear brackets for our pots and pans drawer are broken. See attached photos. Note that these brackets have a stub which fits inside the rail. The inside dimension that the stub will have to fit into is 13/16".If there is no replacement part available, can you recommend full rail and bracket syste ... (cont.)

Hi I ordered 40 of the (40) 32-101 Self Closing Hinge, 2-1/8" and they don't quite line up to my previous hinge holes and I need to see if you have what I need. Here's some pics where it shows the holes don't line up unless the hinge doesn't sit flat. As you can see it looks like my brass ones are ... (cont.)

Swisco Help,I have attached 3 photos. I have a plastic bracket for a kitchen drawer that has broken. I cannot tell you who the rail and bracket hardware was made by. I do not see any identifying information on the rail nor the plastic bracket which identifies the manufacturer. I see the letter " ... (cont.)

One pic shows the slider with roller and the other shows the slider on the other side with missing roller/wheel (close up). I'm wondering if it would be possible to just replace the missing roller instead of the uninstalling both sliders and replacing them -- trying to keep this as simple as possibl ... (cont.)

I built a new drawer for a friend and installed the reinstalled the drawer slides from his old drawer. he called me and said the drawer would not close correctly. apparently he broke one of the rollers that was on the cabinet slide. the picture shows the broken roller I need to get. it is about 29/3 ... (cont.)

Ordered more drawer parts this morning if you could tell me if you have this I'll order 8 of these or if you could put them on the same order thank you previous order # 1396376 Thanks again

I have looked everywhere for these and No Luck Marshall

What is the thickness of the 32-011 drawer slide - the horizontal side where the drawer rides. I need this or a similar product that is between 3/16 and 1/4 thick. The original part was an add on by the furniture manufacturer and used because the drawer was not properly assembled and the drawer ... (cont.)

Please help me find a replacement for this item. My concern is that the cabinet is precut to fit this piece. Will a replacement piece fit?

I need 20 pull out pantry drawer spacers with dimensions shown in photo. Can you help? Base is 2" x 3/4" and height is 1 1/8". Can I purchase these from you?

Do you have hinges that can replace the ones in the photos. They are for a corner cabinet, with bifold doors ? like a lazy Susan cabinet. Thank you.

We bought this island from Sprintz Furniture in Nashville back in 2004. The doors on the island will not close anymore. The hinges look bent. I am looking for replacement hinges. Hinge is 2 1/2 inch. One side of hinge is 1 15/16". Holes are 1 1/4" center to center. These dimensions are the same for ... (cont.)

I need a hinge for upper bifold door for corner wellbourne cabinet. See pictures attached. The part that screws into the cabinet with two screws cracked in half.

Measures From back of boot to the front 2 10/16 Width of base is 1 5/16

I have furniture with the Kenlin Glide Rite system. Researching your website leads me to believe the 32-081 socket is used with the Glide Rite guide system. The Patent information is: 328107 and 3365261. I include 4 photos showing a good and a broken socket. I have a ruler on the good piece show ... (cont.)

will the part 32-012 a good replacement?

Hello...I don't know the name brand of my cabinets or the name of the part I need. They hold the drawer in place in rear of cabinets. Made of brittle plastic. Pictures 1 & 2 show that I have "mended" these sockets. Picture 3 shows a intact socket that looks like I should add some screws to it ... (cont.)

AI 1967 Patent 3,391,420 I think it's 1/2" overlay but the bead edge on the door makes it a bit challenging to get a clean mark for measuring.

I have 4 broken brackets on two drawers. The only markings I have been able to find is a "G" on the rivet that holds the roller in place. There is "RC" stamped on glide on right and "LC" stamped on left glide. The glides are 22" long. The roller has a diameter of 3/4". Glide is angled at the end and ... (cont.)