Viewing all customer Discussions for:

Drawer & Cabinet

Hello, I am renovating an early 70's bath. The medicine cabinet is a Lawson. Beautiful piece but needs the hardware for the glass to slide easily within the stainless steel tracks. I believe all that's needed are the nylon shoes but maybe something would have been installed in the tracks to add stab ... (cont.)

My home is 32 years old and I am trying to replace some hinges on some of my original oak cabinets. I cannot find any identifiers on the cabinets or the hinges. The hinges are slightly odd shaped due to the cabinet door panels having a 45 degree "angled edge" (see pictures). I hope that this descrip ... (cont.)

Had a couple of these drop-handles break due to being cast products. These are from a Hooker office desk. Approximately 5 1/8" wide and drop mounts spaced about 4.75" apart on centers.

RUE TRAK II

Do you have this part?

Several rear drawer guides needed to replace some exactly like this. Made of some kind of plastic, about 2 inches wide by 2 and 5/8 inches tall by about 1/4 inch thick

the # on it was: Blum 78M810 and then I saw -0201

I am making a cabinet and would like to use this hinge do you have something comparable? Thanks

Along with the accompanying photos there are two stamped numbers in the hinge to be replaced: S8590 and 80059. No manufacturer name within the part. Just identifying this hinge would be a huge accomplishment. Should a photo of the hinge out of it's home be required, let me know.

it is the drawer track guide and glide

This piece broke today. Need a replacement. The area to insert the railing is 1.5 inches tall by 1/2 inches wide. It slides to adjust. It is attached to the mount, which is 2 inches wide and 2 1/4 inches wide.

I know this hinge is discontinued. Has a more efficient replacement been manufactured without plastic parts for D3030.67? The holes on the door hinge are 2" on center. The small plastic fitting has cracked/shattered on every one of them. I have eight remaining that need to be replaced and the sup ... (cont.)

What's the broken part called? Are there replacements available- and are they any stronger than original?

Part #652.221.70.00. "Twist on/twist off" hinge that interfaced with a plastic plate that was screwed onto the door.

need 3 sets. Side mount. The outside metal circular tabs fit into metal frames installed inside the cabinet. Cainets installed 25-30 years ago.

Hello, I saw on your website that you have an item 32-019 and it is called Kenlin Tipper glide. It looks like the piece that I am missing for my dresser. I have an Artefact Henredon dresser. My dresser has seven drawers. I also have two night stands. The measurements, look about the same but the b ... (cont.)

Hi, I was looking on your site to see if you have any replacement parts for a 1990 Merlilat kitchen drawer. I have uploaded few pictures one is the sticker another is a functioning part and the other shows the broken one. if you could tell me which part I would need, I would like to purchase a cou ... (cont.)

Hello,I have a roller that broke on our dresser track. Do you sell drawer track that I need. Please see photos.Thank you,George

HiWe live in 25 yr old house and the European style (concealed) hinge to one of our cabinets broke. 170 degrees, overlay door-- there is no brand name on the existing hinge; There are several serial numbers: 664.251.53.01 and 502.361.10-- the original hole drilled into to receive the hinge is 35mm ... (cont.)

Enclosed 4 photos. These hinges only have 652 320 55 01 and Made in Germany. Small piece has 600.20 0. And 11.02. A hardware store looked at my hinges and wrote : opening angle. 110 degree , 48 MM hole spacing, straight arm. As I'm replacing all 10 hinges, I don't need an exact match, just so ... (cont.)