Viewing all customer Discussions for:

Lavatory

My curved shower doors have a gap in the lower corner. It's an American Standard Ovation Series door. I'd like to lift up one corner by 1/8 or more. Is the 10-058 adjustable? Do you have any shower rollers that are adjustable?

Hi, My shower is a framed stall door. There is no seal on the bottom of the door itself. Instead it is in the frame. It appears to be a bulb and is mounted in a track. The only way I could get it out I believe would be to remove the frame. Even then I'm not sure I could find a replacement piece. ... (cont.)

Hello, I have a concealed door knob and latch that has a piece of the door latch broken (see images). I don't think there is another door latch i can use to replace current?? So i think i am stuck with #10-401 replacement kit. Please advise. ALSO, if i am stuck with kit# 10-401, how do i get ... (cont.)

Dreamline shower 1999 bottom door rail guide purchased at Lowes. In a previous post you said it may be your part 10-1039, but I can't find that part in your catalog. Plastic tab with a thicken bottom that fits in a grove in the bottom rail and keeps the door from swinging out.

I'm looking for parts to a maax corner stall w rounded door

I don't see any manufacture name on the shower door. It's roughly 30 years old. Attached are pix

Got a Pasco single shower stall with a swing out door. House was built in 1997. The lower door seal is bad and can't find one. Don't have a photo of the seal but have a shot of the stall. The white seal is a after market one I tried to make work.

I see that you carry the 10-134. that's the part on the bottom of the door in this photo I found. What is the "top part" opposite the bottom roller? The 5 white-ish guides with screws through them?

shower door frame is 27 1/4" wide, 3/8" thick bottom edge, metal strip is 26 1/4". This is a over 20 year old shower door. Rubber and hardware rotted and deteriorated due to very hard water. Attaching screws rusted out.

Hi, I have attached two photos of my door sweep. It would be great if you can recommend a replacement part. Thanks!

I am looking to replace this bottom shower glide. It attaches the lower part of the door to the frame of the tub. Can you please take a look at the photos to see if you have something compatible. Thanks, Jason C

Looking for new shower door sweep gasket - Which one that you sell would be the closest? It has a half moon top Thank you in advance

Assuming this product will work as a replacement for the plastic shower sweep currently installed? Can holes be drilled to match existing screw placement on the door. Picture attached Thank you.

This client shower door roller assemblies top amd bottom now longer work properly. I am not totally sure why except it drags badly when trying to roll it. To make sure i get it right i would like to order all nessesary parts that are used for panel rolling movement. I dont believe there is an ... (cont.)

Hi! My shower door bottom sweep is cracked. I need a replacement, please see the pictures attached if you have any part I can replace? Thanks! Sam

I have a maax shower door installed sometime around 2009 or so. The rollers at the top of the straight (not curved) shower door need to be replaced and I'm guessing any connecting parts at the bottom should be replaced too. I could not find any model numbers, etc but have included the pictures. A ... (cont.)

I have a shower door sweep that is just wedged into the bottom of the door frame(friction fit) do you have anything in your inventory to replace it ?

HOW DO YOU ATTACH A FRAMELESS SLIDING SHOWER DOOR ADJUSTABLE HANGER TO A GLASS SLIDING DOOR?

I need to replace 4 wheels Do you have this part

shower door no longer stays shut because magnet fell out of bracket. door pull is fine. tried to cut and stick magnet strip into bracket as show in pic, but still does not hold door shut. the only marking found is "Unitex" on the glass.