Viewing all customer Discussions for:

Lavatory

Hello, Can I use a frameless shower door sweep like 10-328 or 10-331 depending on glass/door frame size to replace a shower door sweep like one that like 10-324, 10-325 or 10-326? The frameless sweeps look/seem so much better and appear easier to install. I appreciate your help and look ... (cont.)

These clips appear only on the inside door of my shower. I think I have found them on your website, but wanted it she sure if you could confirm the part # please.

Hi..my three shower doors need to have rubber seals replaced. I am not sure the ones I see match mine....it looks slightly different. Attaching a picture...if it is not clear enough, I can try again. Thank you.

It looks like the original sweep (24 inches) is adhered to the metal rail. The metal rail itself does not appear to be removable so I think I need a new flat backed sweep to glue on after I clean the metal and remove the old. Can you tell me what parts I need to replace this? Thank you, Amber ... (cont.)

No markings on hinge. Appears to be chrome plated die cast.There is a latch in the same unit which is marked "Mills", but who knows if both parts are from the same manufacturer.

My sweep measures .155 wide on top of the T, and is less than 1inch in height from top of T to bottom of sweep,and 30 inches long. It's also clear in color. What do you have. Thanks.

I purchased a round shower kit from Home Depot back in 2010 and now all the parts are breaking off so I'm looking for pieces to fix it (rather than buying/installing a whole new one). There's a top roller assembly that totally looks like the it will work with the 10-058 that you've been recommending ... (cont.)

How far from each end of the sweep are the screw holes?

Hello, We have a lavatory partition door knob that is no longer working. The knob is loose and spins without moving the bolt. I have watched a video on line about drilling off the door handle and snapping the new one back in place. Can you confirm the parts and part numbers I will need for the re ... (cont.)

Hello, I need help finding a replacement for my shower door sweep. I would like to get the one with the rail. But here's my problem - The one I have (see pictures attached) measures 24.75" and the holes are 10" apart in the middle and 6" apart on the ends. Do you know if any of your items ... (cont.)

The photos are of concealed bathroom latches. They measure 1 5/8" in diameter. Is the pictured latch a swissco 10-556? If so, what is the correct ADA compliant latch for that door? Thanks, Aaron

Water continuously get under the drip rail and sweep of our hinged shower door and mold forms. The photos show the door with and without the drip rail and sweep in place, I took photos after I had cleaned both. I ordered item 10-326 and don't know if I should screw it on or hold it on with caulk ... (cont.)

I have a corner shower with glass labeled as king glass ANSIZ97 1-1984. The hardware with the spring and single screw broke and I need to get the replacement piece. Any help would be great. Thank you.

How does it attach, is it screwed on or with an special adhesive tape?

I was wondering if you could tell me the diameter of the wheels in this kit please?

Gasket is missing. Do you have one? Looks like it screws behind the water shield. Should I just put a whole new replacement shield with gasket?

I need to replace an All American Metal Corp Knob Assembly i was wanting to know if the 10-556 and the 10-557 will work. I am installing them into a area where disabled people would be using it So would i have to use the 10-557 being its ADA compliant. Hope to hear back from you soon! Thanks! ... (cont.)

The first three mages were taken when the part was off and the last when it was on. photo.jpg and photo(1).jpg need to be rotated by 90 degree to become straight up.

Will this knob work as a replacement of an All American Metal Corp. knob?

The latch on my shower door, installed in 1985, is a rubber "ball" that clicks into a notch on the shower door frame. The ball and notch have both worn down and the ball won't stay in the notch. If I could just replace the rubber ball, I'd be fine. Otherwise, I'd like to find a handle assembly that ... (cont.)