Viewing all customer Discussions for:

Other

Hello, I can not find any identifying numbers, not even sure about the manufacturer, possibly Farley. One of the cast handle mounting threads has broken. I just need the the handle nothing else. Is this something you may have. I think I see something very similar with 4-15/16 hole spacing. Just ... (cont.)

Hi, I have a few of these window pivot bar assemblies missing from my windows. I'm seeing some similar products on Swisco, but nothing exact. Will one of those work? Also, in the picture of the broken slot, I'm guessing the reason the assembly is missing has to do with the fact that the vinyl is b ... (cont.)

Good day. I'm looking to replace these parts for a few windows we have. The number on the part I believe could be either 3540 or 2540. Attached to this correspondence is a picture with the number on it.I would like to order for full complete replacement parts for the window's if possible.Thank you f ... (cont.)

Please Advise if this part is available . Thanks John

I WISH TO ORDER THE CHANNEL BALANCE WITH A BALANCE ATTACHMENT CLIP... 15-198 FITTED. ~~~~~~~~~~~~~~ Full name: malcolm atkinson Channel series: S795 Channel length: 28 Channel stamp: 28B Quantity: 2

Hi, I'm looking for the piece that the handle of my slider is connected to. There are two threaded knobs that receive screws from the mounting plate when put into position. It says "Interlock" on the part. It's from a Harvey sliding patio door.

The crank just stopped working and seems to not be grabbing the gear to open the window. I'm assuming I need to replace the crank and gear parts?

This broken screen latch was removed from a 725 Ellison Screen installed in 2004. Can you supply a replacement part? Thanks, Ben

I have a 42lb single sash window with one broken channel. The bottom plastic fitting is broken and it incorporates a pulley in the moulding. The house is only 4 years old. The channel is 34" long, 5/8" deep, 1/2" wide with a 3375 stamping. I can't see a 3375 to order or the appropriate end fittings ... (cont.)

Hello, I am hoping to find replacement parts for my screen door. Specifically the plastic piece that holds the frame together by accepting a screw.

I had a rock hit my window and it broke the vynle strip across the glass in the center. It is 34 1/4 inches long.

I need help identify one where I can purchase parts to repair/springs the channels are premade vinyl channels with the spring and a plastic Guide inside. There are no manufacture markings at all on the channel or the guide. They are also no manufacture marking on the windows which are architectural ... (cont.)

House built in 2014. Do you have a replacement part? Thank you

Can you identify or tell me where to get the round 'spacer' part which is missing from this drawer. Sending two pics. One with the round part and the other side without it. Could something like a coil drum work for this?

I am looking to purchase weather strip seals for the bottom portion of the window as shown in the attached photos. Included in the attached photos is a snapshot of what I believe to be the window data sticker/plate. Please assist. Thanks!

I do not see this one on your site. I have included the measurements in the photos. I am looking for this in brushed Nickel. This has the rod as it is not mounted at the top or bottom of the door as well the outside of it has the rounded end on both ends to fit the hole. Any helps is appreciated. ... (cont.)

They're Simonton double-hungs, flimsy as heck, so I may need a few extra. Those clasps or whatever you call them snapped off when someone tried to break in. It's a pretty small window so we're pretty sure the burglar was either Elastic Girl or a small child.Thanks for your attention to this small or ... (cont.)

This is from a late 1960's or early 70's Aluminum/Glass patio door. The single wheel is 1 11/16" plastic or nylon. Brand is unknownI'm looking for 2 assemblies please.Joel

I need to replace brand International Patio door lock. This door is very old. Could you please verify if this lock is available? Thanks in advance Tarj

Got this from your website but couldn't find it on your site. Maybe it's an old photo? Anyway, this is the part I need. Do you still carry it? If so, how do I order one?