Viewing all customer Discussions for:

Other

need 2 replacement channels... the "left" one is stamped 2430F... the right one is stamped 2430Q or an "O"? the channel length is 25"... the channel width is 1/2" (9/16 actual)... I believe it is your part #S371-25... Thank you, Bob at 813 508 4826

Need handles and internal locks replaced.

No brand name or parts number on my window spiral balance, it's cased in with white plastic tube or thin PCV tube (which is now cracking). The tube has 34" in length for all windows, while the bathroom window is 24". The diameter is around 3/8".

Unable to find any brand or identification information on the windows. Broken Pivots are marked with L or R only.

I have drawer slides that are soft stop slides. The absorber for the drawer stop has the following part number: AVS421 1BO8BO1. I need some replacements. Do you carry this part?

Hi, Just have a couple questions for you. Is it possible to get the spring shown and the metal track the window rides in? And also, what would have been the purpose of having the entire spring mounted inside (both ends screwed down) the lower sash? I can't seem to figure out any good that it is ... (cont.)

Can anyone tell me the part I'm looking for? It is for a Pella casement window. Do not see any markings or numbers on it

Happy holidays!Please see attached photos. The holes are 1-1/2" on center. Let me know if you have similar cam handles. RegardsJin

The closet door is 20 years old. The only label on it says Sunshine Mirror. No part number or any other info just that it meets safety standards. The last photo shows the back or inside of the door. It was mounted in the bottom right corner. I'd really appreciate any help you can give me. Thanks, T ... (cont.)

Trying to replace a few of these that are missing around my house. I'm not sure how to describe it other than a window lock casement. Thank you!

Hi please see the attached pics, I am looking for pricing on replacement handles and cranks. For the cranks on need both side, right and left. Thank you.

Please help identify the channel balance attached in this email. Please get back to me as soon as you can because I need as quick as possible. The shoe on my current channel balance is straight not curve in the back and measured exactly 1/2, 15/16 and the depth is at 7/8 of an inch(not 1" or 1-3/32 ... (cont.)

Hi Support Team Need some help identifying the window pivot part using the pics that I have uploaded. Pls help Thanks Kane

I need your help to identify the correct replacement channel guides.  Attached are pictures of a balance from a Viking window. The guide is stamped "2840", and measures 5/8" deep, 9/16" wide, and 29  1/4" long.  It appears to match your 29" parts, with a minor difference on length. The top shoe appe ... (cont.)

Window is 72" tall valances are not in a cylinder but has a plastic tube on upper half window is aluminum and about 18 yrs old

Regarding Product Code: 82-043.What's the length(depth) and width of the piece that goes into the lock?Thank you.Dmitriy.

Can you please help with these two parts? We believe the first part is 32-312 but are having issues with the 2nd item. This part supports the drawer in the middle. The drawer slides into the square. The bottom part is broken where the screw is. It's probably an additional 1/2". It's not a bumper. ... (cont.)

I am looking to replace the sash balance for my window. The part says 24S GG BSI 25 (picture attached). The sash measure approximately 25 inches. Would you be able to help confirm the part? I would like to make sure I purchase the correct part from your website. Many thanks, Andy ... (cont.)

I have a double hung Milgard Ultra window (model 3285U), installed in 2013. Currently, I'm unable to easily tilt and remove the bottom sash, because the side locks / slide bolts don't retract all the way.Normally, with this model, you push the sash lock/latch mechanism past the open position to retr ... (cont.)

We are looking for the pictured window latches for a historic renovation