Viewing all customer Discussions for:

Other

This is the plastic clip the spiral balance screws into.

I removed the patio door handle and the latch inner/assy (because the latch didn't catch) and sure enough it fell into the door frame. I am looking for the latch assy for a Wenco door with the 3&11/16 for a 1&1/2 in door width. The handle screws are 3 & 15/16 apart. Yes, I should have watched the ... (cont.)

inside a patio sliding glass door just the lock

The size that I need is 5'10 1/2. is it possible to get that exact size sent to me?

I have this house that was started in 1999 then abandoned after the shell was complete. The frame of the window wraps around the sash. As you can see there is not much clearance between the back of the frame and the sash. Is the backing plate on the screw post sufficiently thin that the sash can rid ... (cont.)

Attached are photos of a storm door lock (Sears?) I don't have a key and the cylinder doesn't seem to be accessible. Do you have a replacement cylinder (with instructions) or a compatible alternative keyed lock? Regards.

I have the part number 34C BS1 which translates to Series 765 Balance, product code S765. I need a 35 inch replacement so S765-35. The balance in the window does not have a sash weight stamp. The window is large, 35 Inches by 32 1/2 for the bottom pane. How do I know what weight option I need. Do I ... (cont.)

Trying to identify the manufacturer of the screen door that these parts came off of. the roller matches you part #84-100. The handle I don't see a match for it on the site, but it has embossed a crown on the face of the handle. any help identifying the manufacturer would be appreciated. ... (cont.)

I have a four door system and the previous owner put car greese to make it role easier. It's a mess. It looks like I need your 81-153 roller and not sure on the stripping. Looks like 3/16th wide stripping. I submitted the pictures for your review. Thanks. Please confirm.

I'm looking to replace my window cranks. I've searched and I found some similar things, but I wanted to verify with the pros before I ordered. I would appreciate your help.

looking for replacement part for Truth left handed operator and arm: operator 45252 arm 40051B Please let me know if you carry this. Thanks Ravi

The removal screw for the balance is behind a portion of the window framing. This is for the lower window only. Do you have any advice on what to do so I can remove the balance. I need to replace them on many of my windows in the entire house.

My question is on Window Corners. Product Code 95-120 and 95-002. What is difference between the two. Do they come in size 2/16 on both ends and 1" long. the 3/16 I believe is wider than mine which are broken.

I'm looking for several pairs (i.e. L&R) metal drawer slide. These were used on wooden dresser drawers in cabinet made by Thomasville for military use in on post housing. Drawer slide is marked Made In Austria, Number: MR20314/400 On the drawer, slide is L shaped attaching on side and bottom edge ... (cont.)

distance between screws appears to be 1.5". This is on a condo built around 1980 if that helps. Thanks.

What is the difference between Series 380 and Series 385 specifically 15-005 and 15-004.

I need a C-9400A-1 straight arm left (i think). What part do you recommend?

Hello, I am looking for some white plastic plugs that go in the perimeter of the moulding around the glass on my entry doors, that covers up the screws on the interior side.These would be somewhat wedge shaped, as they are in the middle of the moulding. The name on the hinge is Penrod, and ... (cont.)

I have a 1980 or so glazing that you did not have. I was looking at your glazing and found the 55-092 , all most the same then your site shows my window and that this could possibly be a replacement for the original, and in just looking at it, I had to agree, so I order it. I install one with great ... (cont.)

Please hep me to select the correct latch part. a sketch and photo are attached. Thank you. W.B. Marked: AS NYC 40 39