Viewing all customer Discussions for:

Other

Numbers 11600-17. On the tab where you screw it on numbers 519. 3. 54. 9. 89.which one to buy and do I need to replace both only one is broke

These are pictures of the sliding glass door handle that is about to break. Need to know where to get replacement parts.

The bolt that locks the bottom of the door (normally kept closed) opposite of the passage door has broken free of the latch arm and will no longer extend into the threshold. My repairman believes it was broken when someone tried to force the bolt to disengage (open). Photos attached here show its ... (cont.)

Item1: BALANCER, WINDOW, 24", WITH TOP BRACKET 344-840, BOTTOM 3/4" WD SHOE BSI(111), STAMPED #2340, QtY: 100 EA Item2: BALANCER, 23", WITH 3/4" SHOE GUIDE ONLY, WITH 103F TOP & 111F BOTTOM, WITH CB9006 & CB9004-WIDE, QtY: 100 EA Item3: Item3: BALANCER, WINDOW, 24", SPIRAL, Qty: 50 eA ... (cont.)

Hi there. We are having issues with several of our window cranks.They each spin open line but it seems to be stripped when trying to spin the window closed again. We have to pull the window in manually. The base of the window crank is 5 inches and the long arm is about 10.5 inches.Do you sell a repl ... (cont.)

Good morning, I have a window that isn't connecting very well. Its a double hung, vinyl window that isn't catching very well where the two windows meet in the middle. It has two latches, one on each side. I assume if I replace the latches, that should do the trick.

Channel Balance Series: 795 Channel Length: 27 Channel Stamp: 27C Quantity: 2 Need 15-198 balance clip attachments 15-198

Looking for these particular ones

Some part #s on the Truth entry guard- 30842R; 20810 and 30744. Need left an right for 22" windows.

This closet door continues to come off the track due to age, wear and tear. As you can see from the photos, the track is pretty beaten up. I'm not sure about the rollers, so I included photos of them. It is in my daughter's room and I'd like to keep it if I can for cost reasons. There is a crack in ... (cont.)

Hi, My 1970s shower door isn't gliding smoothly, and I think it's because these bottom pieces are worn out. There are four of them, two on each door. The pieces measure about 5/8" x 3/8" x 3/8". The door/frame has no markings, but the glass is stamped with "Arm-R-Clad CE Glass Safety Tempered ANSI 2 ... (cont.)

I have the Florida extruder's sliding glass doors. Brand is milestone I need the frame piece to an 8 foot door that also would hold the handle.

I need the "stabilizer " part for my window. I have ordered parts from you recently and they fit perfectly.Thank you.

I am trying to find a replacment plastic back end support bracket (if sold individually it is the rigsays it is manufactured by Hettich and on that metal bracket has stamped on it Hettich 602 CR. I am providing pictures of the bracket and the metal slide. The unit has been installed for awhile (20+ ... (cont.)

Need a new sliding door handle as this ones bottom screw broke

Hi, I'd like help replacing the entire crank system of this casement window, including the cover and handle. I think it is a Jeld-wen but can't be certain, as the elements have nearly destroyed the window's I.D. tag (see photo). I believe this is a RH crank? Many thanks in advance! ... (cont.)

My windows don't lock properly. These windows are at least 25 years old. The locking handles are too loose and have no grip to keep the windows locked. Is there a way to repair them by changing small parts?

No numbers. Part of the plastic broke that hold tension.

9 1/4 long handle 4" distance from screws Middle lock outside , offset

The brand looks like "Truth" On the base is the number 403272. On the top arm is the number L30841 On the back of the sentry guard arm is the number 30470LH