Viewing all customer Discussions for:

Other

I have pro shield casement windows from weather shield that I am needing to replace.

Searching for 1 plastic roller for aluminum window. It appears to snap in small hole on the outside of the frame. House built in 1961 California.

Looking for the correct part number for a mortise lock mechanism for a Pella 750 series slide glass door. Is it 82-247? I can't believe this part is almost $200 but I want to make sure I buy the right part. Please advise.

I am searching for what I believe to be a drawer track back plate. The one in the picture was manufactured by Ronthor NYC. The square is 15/16" to the exterior edge of the square. I suspect the top which screws or staples into the back of the cabinet is another inch but as you can see the plastic ... (cont.)

I'm looking for screws to fit my nami windows. Can you help. Dave. Thanks

Hello, I am going to order Oil Rubbed Bronze Atrium Door Lever Lockset Product Code: 82-398, but would like to use the same key at least with 5 of the 6 that I need to order. Is that possible?

Hi Swisco - i'm unsure of which pivot bar to buy for this window. As you can see there is a lot of rust and the current pivot bar has basically disintegrated and some parts are inside the lower portion of the window. Do you have enough information here to determine the part? Other parts i am orderi ... (cont.)

Hello - I am in need of a replacement surface mounted tilt latch in tan. I don't see a similar product on your website, even in a different color. Note this is the left side and it has a "night latch" pin to secure the window while open. Thank you.

I'm a return customer and have another broken balancer and shoe that needs to be replaced. I need both sides for the window. I will send photos and info for the window. Thanks!

Hi, I have a number of different window sizes that need these parts replaced. I don't know their make or model. Could you let me know what other information you need so I can order them. I hope that the 2 pics I've enclosed help. Many thanks, Ian

Hi all, Hoping to confirm a part number for 6 left hand replacements. Hole spacing is 1 1/8 x 5.25 with a 2 3/8 arm. Some of the arm attachments seem to be via c-clip and others by threaded grommet. Also looking for an extended or straight crank handle. One was installed in a corner beside a door ... (cont.)

I need aluminum window glass glaze bead shown in picture

I have these plastic parts at the end of my metal drawer rails for a kitchen drawer. One of them has broken and I need to replace it, but I can't seem to find something that will work. Any help would be much appreciated.

Hello Swisco, I will be ordering American Craftsman parts for my windows and door slider 6' can You tell me the correct slidder wheels forthe 6' American Craftsman Slidders? I will be ordering also American Craftsman Double hung parts Pivot pins, Coil Balance Springs 16.7lbs window weight and Ti ... (cont.)

Plastic piece that squares the window. 4.5" x 6.0" 101/IS 2-97. Need the long piece. To start with. Still looking into other issues with the window not staying up. Thank you! Maria

Hello,Can you help me? I am looking for replacement rollers for my doors. If you can identify and provide me with the correct replacement. Looking at your site it looks like a 81-023 it has a 1 1/4 wheel. I would need 8 -10.Thank you Greg

My window is jammed in the fully closed position. I noticed some pieces of broken plastic when I locked it. I'm not sure how to remove window now that's it's jammed closed. Do I remove the terminal clip and try to pull the window up? The markings on my channel balance are 26 4 6V CMC 1 and the leng ... (cont.)

I need a replacement for my window as the one pictured I upload snapped. Thank you! Tamra

Hi, I need the slider track and brackets for a 92"L x 39"H SWC Vinyl Window, Fixed center, with a horizontal slider on each side. Can you help me find the parts?

Hoping to find these. I need a complete set. I'm missing one of the pulls.