Viewing all customer Discussions for:

Other

I need the hardware for these doors. 24 inch doors

I took this off the right side ( from inside of home looking to street) of a non tilt metal dual pane atrium window. The window will not lock. seems to be 1/8 off from latch catching.The latch on the movable window needs to go down about an 1/8 to catch or top window up 1/8" " I checked the fixed w ... (cont.)

Hi, After the window is opened, it cannot be hold there, it will fall off and close. Is the balance broken? Please advise me buy the parts to fix it. Thank you! Tania

Hello I am searching for a replacement part for my late 50s sliding door. Do you happen to know of a part that would replace or might replace this? THanks!

Hello, I'm trying to id my window balances The length of the window balance is 28" and the stamp is 27-3 EFC CMC 54. I will want to purchase four of these. I look forward to your response. Please let me know if you need any additional information.sincerely, Ernesto

These balances haven't any u-shaped coverings that conceal the spring and other operating mechanisms. I also haven't seen this design on the website. Maybe they're obsolete and you have a new design? Thanks in advance.

Looking for window grill fasteners with barbs to replace the terrible little spring fasteners. Internet search showed your company had them, but can't find. Becky

I have 2 Stanley doors that are about 25 years old. I ordered (2) 58-008 seal kits. Our doors have a compression seal on all 3 sides, right left and top. The kit has 1 long compression seal and 1 long magnetic seal and 1 magnetic seal for the top. Do I have the correct kits for my doors? I also ... (cont.)

One window weighs 28 lbs. The number in it is 29- 4 da2 cmc7 The other one weighs 30 lbs. The number on it is 29-9 ca2 cmc4. I need a set of each and sets of the sash top. Could you please tell me what to get? Thank you.

Hello, I have Pella double hung windows that need new balance channel/spring. They are hidden behind a piece of snap in plastic jamb liner. The channels measure 40 inches in length. The channels are 9/16 inches wide and 1/2" deep. The two channels sit on a 45 degree angle on a single bracket att ... (cont.)

These hinges are from our buffet which we purchased about 6 years ago. They've become bent over time so that the doors on the buffet no longer close and we'd like to replace them. We're not sure who the manufacturer is, but we believe it's AAmerica. Do you have any suitable replacement hinges? ... (cont.)

The door handle latch broke when it was being shot due to extreme cold

I'm looking for Window balancers that will fit this style along with the pins that sit inside the bottom of the window itself.

1/2 in overlay cabinet, markings Mepla 698.253.50.01 348 253 51 02 Made in w. Germany

Hi, I have a Pella picture window in the family room which has a shade between glass. The shade operated through a handle that works on a pulley mechanism. Over time, the pulley cord has started slipping through (the jagged structure that holds the cord in the lever is flattening out. For now, I cut ... (cont.)

I need a replace balance

The metal channel is 13 1/4 inch long

Hi,Looking for the channels (34B), pivot lock shoes, and the pivot bars. Photos are attached.Thank you,Steven

My rental house has some old vinyl windows that has sever sun damage. The vinyl is so brittle that the handles and tilt latches have crumbled and broke when opening the windows. I would like to get new tilt latches and "L" shaped handles. Do you have these and do you know the brand of these win ... (cont.)

I want to add a lock to a western window systems slider. The hole for the mechanism seems to be about 9" by 1 3/8". Do you make a part that will fit this?