Viewing all customer Discussions for:

Other

Cord inside channel broke.pulleys are worn so a new complete channel is required. A # on the channel is 2630 if that is of value.I think I would order two new channel to replace at the same time.Please help.

Hello,I cannot find a model number on my windows but these to me look like 150 series correct? I found the number #6 and #7 posted on the coil themselves. I just wanted to see if I am order the right parts below.#7 (S150-7) coilpivot shoe (15-140)cap (15-144)support barrel (15-145)#6 (S150-6)ThanksT ... (cont.)

Hello, I need to buy the locking mechanism along with the black-ish handle. I'm trying to call you but the phone call doesn't go through. I found the part number for the lock (82-227) but I'm unable to find the handle part number. Can you please give me another phone number of yours so I can call a ... (cont.)

Hi I need to limit the operation of these windows so that they only open 4 inches. I know you have a sash stop limiter. But it seems a little bit hard to install. Any other ideas on how this could be done?

Good afternoon. I have two window sashs requiring the coil balance replaced. One sash weights 13.6 lbs and the other weights 15.6 lbs. I couldn't find any identifying marking either on the housing or the coil spring. I measure my housing and it is slightly smaller than than the S161 and S210. My ho ... (cont.)

Will this part sill work since your part measures 9/16" mine measure 7/8" or 13/16"?

Hi, The right side of my double hung window balancer is broken. I couldn't find the right part on your website. One the plastic piece where the window connect to showed number 5 on the balancer. Can you tell me what do I need to get this replace? I also upload the left side where it is still g ... (cont.)

I determined that I need pella product number 39-397 but can't determine if it's right or left?

Attached photos of broken balances and window stickers I'd like both the 10R and the 11 , which is what they're labeled. Ones the front and ones the rear window, double hung. Can you tell which repair balance I need from the provided pictures? Thanks

The furthest dimension is 5 1/4". The next dimension is 3 5/8" I need the lock handle to be horizontal or 90° when unlocked vertical when locked.

I have Marvin windows .. can you identify the window crank mechanisms I have and window replacement parts / cost?

Please help me identify this operator as I could not find it in the catalog. The exterior screw holes are approximately 4 1/4" on center. The swing arm is approximately the arm that attaches to the sash has a plastic glide and not sure what dimension you need but the ruler is on it. The inside curv ... (cont.)

I would like to replace the rollers on my mirrored closet doors (2). They are approximately 30 years old. I will upload a couple more photos in a second email.

Can you let me know if you have this part?Thanks Tim

The first pic is the broken handle for a entry door the second pic is what it is supposed to look like. Do you have these?

Hello, I have the same situation. Need to replace this 13.5 inch balancers for my Milgard window. Can you send me a link to purchase new ones. Thanks! Armando

I have old wood windows. The balance springs are shot... generally the ends of the springs have broken allowing the spring to retract up into the channels and no longer provide support for the window. In the first photo, you can see a functioning spring that I have pulled down for viewing. A clip ... (cont.)

Hello. The lock on my sliding door does not latch. Attached are 4 pictures. Unfortunately, I don't have the product name.

I have a 2008 Semco patio door with no handles. It already has the mortise. I am looking for handles that have a lock that works with what I have installed

help, i replaced the tension rod. window was still falling. I see the plastic piece in the track that holds the window in is out, see pic. what to do?