Viewing all customer Discussions for:

Weatherization

Need to replace the weatherstripping on my Windows. It has become brittle and falling apart. Sending photos of what is on there but not sure which size to order. You have two the .270 T-slot or the .187 T-slot filled bulb weather seal. Can you tell by the photos I sent which one. What is your retur ... (cont.)

Hi, Do you have anything in your inventory which best matches the t-slot profiles in the attached pdf and pictures? These are gaskets used on a 1960's wildcat travel trailer. Let me know if you can help. Thanks! Alan

7' Commercial door needing new weather stripping. The existing strip has only one band of bristles and is approximately 15mm wide. Do you sell a replacement part?

I need to replace my Forever Door bottom sweep. I purchased Item Number 58-176 which arrived today. Unfortunately, this item does not solve my problem. The width of the U-Channel is good. However, the depth of this item is 5/8" x 7/8". This is insufficient to cover the door bottom properly. The ... (cont.)

the weatherstripping appears to have a cord inside of it which is stuffed inside a groove in the door frame. I haven't been able to find a similar product online.

Could not find our kerf mounted, foam core bubble seal on your site and hope you have it, or something similar enough to work. Three pictures included. Please let me know if you need more information. Thank you for your help. Catherine W

H-R20 48x78 H-R30 36x64 AAMA/NWWDA 8500/850

I have some questions about weather striping and about the track covers. I attached some pictures. Can you tell me if you think the cap in my estimate is the correct caps? Also how critical is it to change the gasket on the glass. I cannot take a cross section of it with out tearing the door apa ... (cont.)

I have 1997 ceritenteed windows I have installed part # 58-127 3/16 x1/4 weatherstripping,no problem however on the bottom of the top window the seal appears to be 3/16 x 5/16 wool pile which I cannot find on your web sight any suggestions?thanks Rick

Looking to replace the rubber sweep(s) on a storm door. It

looking for retainer strips to hold glass in

Need plastic weather stripping at bottom of window. It is brittle from age.

Hi my name is Vitaliy and I

I have a Stanley front door. The door sweep is ruined and I am trying to get a replacement. The door sweep slides into grooves in the bottom of the door. It DOES NOT slide around the door. I am enclosing a photo. Overall width of Sweep 1 1/2 inches From outside to outside of slider is 1 1/8 ... (cont.)

I have a 6'x8' steel double door that has magnetic weather stripping at the top and in the astragal. The side jambs have a compression strip. I can't seem to find the weather stripping to fit either the width or height. I can put 2 36 together to fit the top but I won't be able to get a piece for th ... (cont.)

Hi: I hope the pictures turn out because I haven't the Foggiest what I'm doing. I have more photos.

I am Looking to replace the original weatherstripping. This window made by Certainteed and we had it since 2001. Attached is the picture of the strip. Thank you for your help. Michael.

I have about 22 windows installed 14 years ago and I find that the bulb seals (at bottom of each window) all warped and brittled. I want to replace at least a few windows immediately. I have taken pictures (attached) and measured the diameter of the bulb ~ 0.25 inch, and the dimension of the kerf ... (cont.)

I have a sample from a window that measures about 1/4" wide x 1/4" tall with a fin in the middle. I'm not sure if a 9/32 will fit, it was tight pulling the "8/32" piece out. Will a 3/16 base work or will it have too much play? Also will 3/16 height be too short? Please advise. I have 18 windows ... (cont.)

Need help identifying this form of bubble seal for a vinyl window. The t-slot is ~.187" and the oval bubble is ~.354" x ~.157"