Viewing all customer Discussions for:

Weatherization

The weather strip consists of a rubber or vinyl portion that is secured to a plastic portion that slides into the slot of the window frame. Widest portion is 7/16'' which is the rubber portion. Width of the plastic portion that slides into the slot of the window is 7/32'' Height is 3/8' ... (cont.)

I need a sweep for my storm door that is about 8 years old. the warranty registration # is 90567-321-090427. Can we tell from that number which sweep I need? Tom

Im trying to find a replacement seal for capitol windows.

I am trying to purchse the weather strip as shown in the attached photo. I have also attached a dimensional diagram of the weatherstrip. It is on a full French door manufactured by WeatherShield in approximately 1999. I need 6'. Can you tell me if you have this and how much it would cost? ... (cont.)

Door opened to the left. It's a door bottom sweep.

I have aluminum windows thet have a T-slot for the weatherstripping The slot measures wide. I cannot determine the height because the pile is now compressed and worn. It appears that the pile sticks beyond the window at least 1/4 to 3/8 of an inch. What siaxes are available and what would you r ... (cont.)

I have some older Home Depot vinyl double hung Windows. The bottom weather stripping needs to be replaced. It looks like the weather stripping locks into a 3/16 inch groove on the front of the sash and has a 1/2 inch foam filled bubble. Any idea what I need to fix this problem?

Please review the attached photos I have placed. Please advise me on where I should start in order to rectify this matter. Thank you in advance for your time and help. With gratitude, Todd

I need to replace the weatherstripping around my back door. It looks close to the Pella Push-In Bulb Weatherstripping (part 58-181), but from the picture, you can see that the piece that fits into the gap to secure the weatherstripping is in the wrong place. Any thoughts?

Need to identify the name and type of weatherstripping this is to order replacements for our 10 year old Amerimax vinyl windows.

I have a relatively old Cole Sewell storm door which is in fine shape except for the vinyl part of the door sweep. The metal part is 36 inches long and the vinyl piece is 1/8 of an inch by 1 inch. Do you sell this? Thanks so much.

Looking for replacement rubber/plastic weatherstripping for a Pella sliding glass door installed in around 2001. See attached picture of cross-section of the weatherstrip Rgeards Scott

I have about 35 wooden Marvin casement windows that need replacement weatherstripping. I have some old replacement parts labeled V673 but they are too brittle to use. The sash dimensions are 45" x 18". I'd like white weatherstripping. Can you help?

The door seal at the opposite end is torn and I want to replace it. The bottom seal assembly is screwed to the door. Overall door width is 31 11/16 inches. I cannot determine the manufacturer. I am located in Pennsylvania just north of Pittsburgh.

I have vinyl windows in my home. One of the Windows is missing the strip at the bottom on the interior of the house. It allows air through and is drafty. Can you help me identify what part I need?

looking to replace on 9 window's

we are restoring some historic wooden casement windows that have black pile weatherstripping on the top and bottom edges. it is 3/8" wide and 1/8" high. I think we could get away with a bit of variance on the height. the width needs to be 3/8". the way it needs to be installed, it would be prefer ... (cont.)

I need the wool pile on three sides of my slifing glass door. BUt I also need that sealer that runs at the bottom. How do I find that one?

Need Cardaco window seal replacements for kitchen casement windows. Bottom and sides. Don't know the model number. House was built in 2001 so that is about how the windows are. Glass is double pane. Any suggestions would be extremely helpful. Thank you Greg

I am looking for a vinyl sill angle for a Silverline replacement window. It will fit the generic casement window I am looking to finish. Has to be at least 45.5 inches long.