Viewing all customer Discussions for:

Weatherization

Need help locating this weather stripping for my in swing door. Thank you !

Hello, I want to make sure I am ordering the correct part for my door. Presently there is magnetic weatherstripping on the right and top sides of the door. Please see enclosed pics. Do you have this in white? The length I need is approximately 79" for the right side as that piece is tearing from exc ... (cont.)

I matched part #58-164 to my window fairly easy. Can i use part # 58-171? The peice that slips into a pre-existing groove in the sash on part 58-164 is 3/16" and 5/8" over all in height. Part 58-171 is in 100 th. measurements. Part 171 has a Foam Filled Bulb is that better than 164 vitch is ... (cont.)

Hi, Looking for a window seal or glazing product. Have sliding wood windows and this seal is in the permanent window where the other window overlaps when shut. Thanks for your help

I have a 3 glass Marvin casement window that is 37 years old. The window wood and glass are in good condition , but the weather-stripping in not sealing. Is your product #58-053 (White) a replacement for my Marvin casement window?

I am trying to replace the weather stripping in my windows. I believe they are MW circa 2001. The measurements are as close as I can get. The piece is pretty mangled. Thank you

Need 45 ft of both sizes

I am having trouble replacing the rubber weather stripping to this door. Registration number 0731970028 141 Also if you have key replacements for the handle Lock Emtek 322 if that is available also. Thank you

I'm doing a repair job at our town library and would like to install weather stripping between the main entrance doors. They are 2 wooden doors that meet in the center and have no weatherstrip now. The gap is 3/8 ", and there is no channel in the edge of the door. Can I install your astragal styl ... (cont.)

1/4" from bubble 1/2" overall length

this came off a front entry door that has side windows that pen up on ecach side . this weather stripping came off the window frame to seal window when closed the round part looks to be about 1/4 inch from the face of the round bulb part to the first bend is 1/2 inch the leg that goes into the ... (cont.)

I need to replace the weatherstripping that is mounted on the inside of the window frame that ensures a weather tight seal when the window is closed. The 58-178 rainstrip shown on your website appears to be incorrect. Can you supply the correct part and installation instructions ? I need to replac ... (cont.)

I am looking for replacement bubble weather stripping(WS) for Stanek windows installed in late 2002. The bubble WS slides or presses onto the "T" bar that runs the length of the casement window sill and not on the swinging window. The bubble is 1/4" O.D. The top of the "T" bar is 1/8". The bubb ... (cont.)

I'm looking for replacement for weather stripping on double hung windows. The windows are wood and have a channel for pushing strip in. The strip is on the top, middle, and bottom. See pics attached.

I need weather stripping for Certainteed window model B31404 windows

I have a house with wood casement windows. The house was built in 1987. The marking on the screw out assembly says "Truth". I am assuming these are the brand of windows? You can see by the pictures what kind of weather stripping I need. The width of the actual window is 1 1/2 inches wide and the ... (cont.)

I ordered bubble seal but the "T" is to narrow. I need a 1/4 or 5/16 "t" . the one I ordered is 3/16 and is too small. Do you have it in the other sizes in white? Also I need to do a return on my order. Thanks .. George

Tom, I ordered a roll of 58-002 to replace 45 year old weather stripping on some old boat windows in a 1969 Chris Craft. It appears that the old pile, whetever is left, was adhered to the SS end cap on the sliding glass. I realize the 58-002 is not adhesive backed but it is the right size. What ad ... (cont.)

I would like to locate a replacement part for the weather stripping, removed from a door installed in 1971. The door has a sticker on the outside-bottom labeled "Atlas Architectural Metals, Inc." The weather strip sample backing measures 1/4", and the "felt" measures approx. 1/4". The backing i ... (cont.)

Do you have a weatherstrip that will replace this?