Viewing all customer Discussions for:

Weatherization

I have some Norco casement windows from 1992 that need new weatherstripping. Here are a few pics. Do you have the correct weatherstripping or recommendation of another solution? Thank you

Unknown door manufacturer. Circa 1999/2000 swinging patio door.

Rubber weather seal for a patio door screen...1" wide x 80" long

5/16 bead with a 3/8" overall length measured from the point of the arrowhead to the top of the exposed bead.I need to order these beads asap, your quick reply is appreciated. I have a 4500SF house and probably need thousands of feet of these materials.This is to replace a prior installation that i ... (cont.)

We have MI casement windows with severely cracked weatherstripping and would like to replace the weather stripping. I have had no luck with MI customer service, and thought you might be able to assist. Windows were probably put in 2008. I was not able to pull it out in one piece for a decent photo. ... (cont.)

Weather stripping for a viwinco casement I think. Approximately 3/8x 1/2Thank you

Need weatherstripping to prevent water from coming under this door. Do not know the make of the door. The entire width of the end of the door in the photo is 1 7/8". The width of the space in between the tracks is 1 1/4". Can't seem to find the product that fits this. Can you help? Thanks ... (cont.)

Hello, I'm looking to replace the worn-out weather stripping on my BFRich windows. I included pictures of the existing stripping. I would rather get something with a longer lasting material if available. Thank you! Clair

Looking to replace weather stripping on CARADCO casement windows installed in 2003. I have already done cranks and while doing that noticed substantial deterioration of the weather stripping.

This rubber stripping around our casement windows is worn and sticky making it difficult to open and shut the windows. Can you identify a replacement?

Do you carry replacement side and bottom felt weatherstripping for certainteed windows

Hello,I have a Certainteed window that needs its bottom weatherstripping replaced. I placed an orderfor your 5' Dual-durometer Weatherstrip (58-164-5) because the dimensions matched. The product seemed like a good fit (see attached photo) but unfortunately I think the T is too rigid. The original we ... (cont.)

Would you please advise if you have a replacement for this weather seal for my vinyl windows? It measures 1/2" (facing) and then another 1/2" underneath.Thankyou in anticipation of your assitance,With Kind Regards,Patricia

HELP!What I ordered was 10 packs of 58-171 but the bulb seems to smaller as well as the T. I have only used one pack.Thank You,Jimmy

Hi, Our windows were installed when the house was built in 1997 and I am looking for the rubber and felt piece that is on the bottom of the window to keep any air our. The model is a series 2000SH DH-R30/35 Thanks, Steve

we have double hung certainteed windows purchased in 1994. The bottom sash has a rubber weather strip on its bottom edge that rests on window sill that has shrunk and needs replaced .The window itself has the marking AVC92. do you have this part?

looking to see if you have the vinyl insert with the rubber gasket for GRW. Quite old over 35 years old. If you do have them,I will email you the size and number of strips needed. It is not the felt stripping. I believe I have to loosen about 6-8 screws in the frame to slide this in. thanks den ... (cont.)

This small insulation strip fits in a track between the up and down window. The insert to the window track us 1/4 inch wide with two grooved flanges.The bubble compressed but looks like it was 1/4 inch or less.Images are above Do you have a replacement insulation strip please send part numberPs I'll ... (cont.)

We can't find an exact match on your site.? The .270. 58-171 and the .187. 58-182 look similar, but where they fit into the top of the window, it looks like a different fit -- only one side sticks out ( on ours, both sides protrude) and the part that sticks out is different. Our piece matches the ... (cont.)

Please see the attached photos. The seal on the side of the door frame is about 3/4" wide and the kerf is 1/4". I also need the bottom threshold. I think this is an old Ademco atrium style door. Thanks for your help!