Viewing all customer Discussions for:

55-029 3' Snap-in Glazing

If you have I need order

Hello, I am trying to find the black vinyl strip which is placed outside edges of the windrow to protect water from entering the home. I have searched Home Depot, Lowes, online and cannot seem to locate anything in close relations to it.I am hoping you can be of assistance to find the same or if no ... (cont.)

I need four of the white things in the top corner of the window in the first picture. It seems to hold the spring slide in place. I need 52" of the white extrusion shown in the second picture. It appears to be a seal between the top and bottom windows. Thank You

trying to find matching or close as possible bead to this ...not sure if it is bronze or gray colored, it is exterior window bead/glazing

Above are a couple of pictures of a balance cover that I am currently looking for as well as the beauty ring to hold the glass in. This is for an apartment community so we will be ordering on a consistent basis. Thank you for your time.

Can you assist me in identifying replacement window glazing? Thanks.

Swisco Folks:Just spoke to one of your reps and I've uploaded two photos of Milgard Balancers for identifying the proper replacement. that I need a replacement for two of them as springs are rusted.Stamped number is 26-CLength end to end metal (not including white plastic) is 27 inches. I need two ... (cont.)

Could you please tell me if you have anything that will work for these windows. The plastic is brittle and I need six, six foot strips if you have them. Thanks, Dan

Need to replace glazing bead on approximately 14 year old windows. Information on window: NAMI. ANSI/AAMA/NWWDA 101/I.S.-97. ASTM F 588-97 Code: CFM Rating: HR35 Series: 40 Aluminum SH MST: 3870/4060

I believe this is a hallmark window

Greetings. I have an exterior octagonal window mounted in brick. The windows "trim" which may be called the glazing bead has cracked and is falling off. This does not appear to be a "seal" but is more like snap in trim. Do you offer replacements? Photos attached. Each "side" of the "L" shape i ... (cont.)

I have no photos of bead removed. relevant measurements are: Inside glass (to edge of frame): top panel: 33 1/4 w x 27 h bottom panel: 32 w x 27 h inside frame to frame - 34 1/4 wide outside glazing strips" top panel: 28 h x 34 1/4 w bottom panel: 27 1/2 h x 33 w visible lip on glaring strip: ... (cont.)

Trying to find the replacement glazing strip for aluminum champion windows. Each leg is 1/2 inch long. Thank you

I'm looking for the glazing bead for a H-R Series 375 SH window. I only need enough for the top window. Thank you!

We are in need of snap in vinyl glazing strips to replace the ones that are warped and faded. We would like to get it in brown or black if possible. can you suggest a replacement, please. Thanks!

Hello I can't seem to find a fit for this glazing bead used on my aluminum framed windows. House built in 2004. These snap in and trim the edge of the glass from the outside. The angled barb snaps into a slot in the aluminum frame.

Hello, Windows are aluminum, about 20 years old. Glazing is an approximate V shape with a groove at the top of the V. The inside edge of the V has a slight outward bend at the bottom. The outward facing leg of the V is 5/8" and the inward facing leg is 9/16". No markings found. Color of strip is bla ... (cont.)

I tried Swisco's 55-017, but I think I missed the mark. I also prefer a smooth, rather than rippled, surface. What do you recommend?

It appears it may be Krestmark 900-14895W. There is a possibility the last home owner already changed it from the original because it doesn't appear to fit very well in window. Anyhow, thoughts? Please advise. Ian

This is a section of the vinyl glazing bead from the exterior of my windows that was damaged in a hail storm. I have not been able to locate a replacement that matches this design. I have not been able to find any identifying markings on the beading or windows. Any help that you can offer in ident ... (cont.)